ZoneDirector

ZoneDirector

ZoneDirector

1.7K

  • •••
ruckus 1200

Have a 1200 on the latest firmware 10.5.0.0 build 190. some clients are either: 1. loosing the pw for the wifi point 2. loosing the ip address on the client, but teh  1200 clearly shows the mac & ip address as authorized. if I go into "client connectivity" then start a test, it is

Question

24

4

0

Ruckus ZD1200 Guest using external captive portal with Cisco ISE

Hi All ZD1200 ver 10.5.0.0 build 190  (ip:10.1.100.30) cisco ISE : 3.0.0.458 (ip:10.1.100.29) I want to use Cisco ISE captive portal for guest login. The device cannot redirect to URL when access the guest SSID. Ruckus ZD1200 config: Wan type: Standard Usage Authentication Method: MAC Addr

Question

32

2

0

Adding TLS version support on vSZ-H

Hi all,   I have a vSZ-H controller and was recently asked question by a client regarding TLS versions. They want to switch off TLS v1.0. After looking on the web, i am still struggling with this topic. I have managed to determine (using debug commands) that our controller only appears to sup

Question

8

1

0

ZF2942 Upgrade to 9.7.0.0.220 causes problems

Upgrading standalone 2942 AP from 9.6.1.0.15 to 9.7.0.0.220 makes only troubles for us. I have 2x 2942 standalone AP's. After upgrade both of them needed factory reset to gain access to the web console. Also I had to reconfigure from scratch. Thats bad... But after upgrade I faced issues where

Question

 • 

Answered

18

10

Issue with 9.7 on ZF2942 on ZD controlled AP

Not to hijack, but I have a ZD3100 and 51 2942 APs...and upgraded to 9.7. Same symptom, connected clients became disconnected clients. Average 300 users total then averaged 51 or so, a LOT of APs have zero clients...oh the horror. Case opened, but no joy. Opened forums, I see this, and I

Question

9

3

ZD 1200 System settings and Event logs disappear

Dear all,        A few days ago, I configured  2xZD1200 system settings( name, IP addresses,mgmt interface,vlan, etc...) and done smart redundancy as well. And today when I log in to ZD, I see no data in system settings and cannot view events, logs tabs too. It keeps sho

Question

46

1

0

Upgrade firmware for ZA1200.

Hi everybody, I have a wireless controller ZD1200 model runnig 9.10.2.0.76 (MR3, Refresh 76) firmware version and APs T300 and R610 series, my question is: what is the recommended version to upgrade it? And what is the procedure to goal this? Thanks in advanced! Nice day,

Question

34

3

0

ZD1200 dead?

Hi,I have a ZD1200 which controls around 8 APs setup, however this looks to have died.Looking at the controller, the power and status lights are solid green and never blink, the lights on the LAN are both solid green showing connection but they currently NEVER flash to show data being transferred.I

Question

 • 

Answered

214

3

Zone director RADIUS Accounting to Pusle Secure NAC

hi ruckus team, I have got issue within my POC in the customer, We are running  zone director to create Authentication RADIUS accounting to third party NAC, it is Pulse Secure. the issue is accounting service still running in Pulse Secure event the client in zone director have already disco

Question

16

1

0

Total number of dropped downlink frames

Hi, what exactly does the following show(besides the obvious)? ruckusZDSystemStatsWLANTotalTxDroppedFrm 1.3.6.1.4.1.25053.1.2.1.1.1.15.21 Total number of dropped downlink frames.  is there any sort of "ballpark" figure, and if so how would you go about reducing it, or is it all part of

Question

9

0

0

Important Announcement

Announcements

Categories

View More