Switches

Switches

Switches

526

  • •••
U

Accepted Solution

The switch is rebooted Brocade ICX 7250-24P

Good day! I'm new to this, but I got this toy from a former employee))) I tuned it up, but the next day it just simply rebooted to the factory settings and that's it! I can only enter it through boot, and if I reboot, then on the command line it simply does not respond! If someone came across this,

Question

40

3

0

Accepted Solution

Port MAC Security Question

I am reading about "port MAC security" in the Fastiron Security Guide. We may choose to use this instead of full blown 802.1x auth on all ICX end-user access ports. It is not clear to me though - MACSec appears to be a separate licensed feature, And is only supported on 7450 and better devices. Doe

Question

33

3

0

Routing and ACL. To direct traffic to firewall

Hi, I have a very unique setup witch I would like to implement in the company. We have a Stack of 7850 as Core Router. We got up to 100 VLANs implemented.I plan to route some of the VLANs in the Switch Stack eg. VLAN1 to VLAN2 is routed over the switch. Same with VLAN 3 to VLAN4.To the firewall

Question

38

1

0

Accepted Solution

Official Solution

ICX 7850 egress ACL not supported with untagged vlans?

Can anyone explain why this is the case? From the 08.0.92e documentation:  On ICX 7850 devices only, configuration of egress ACLs is blocked on any virtual interface with an associated VLAN that contains an untagged port. And sure enough, when I try: (config-vif-1234)# ip access-gro

Question

38

1

0

ICX Vsz upgrade failed

Hi guys does anyone know why I have this error while trying to upgrade icx switch trough vsz? Connection no response, please try again later. (last command: copy flash flash secondary)

Question

30

7

0

ICX 7150-C12P temperature sensor questions

So I'm a Lennar home user here and stumbled across 2 temperature questions I was curious about. 1 - Does anyone know what the different temp sensor locations are in the switch? Best I could find was an old Terry Henry vid about the 7250-24P and sensor 1 was 'management thermal plane' and 2 was P

Question

80

0

0

Accepted Solution

L3 Premium License Problem

Hello, I installed l3-prem-2X10G license but my ICX 7250 does not have L3 features. What could be the problem? I reloaded the switch but it is has l2 features, not L3. ICX7250-48 Switch#show version Copyright (c) Ruckus Networks, Inc. All rights reserved.    UNIT 1: compiled on Jan

Question

86

3

0

how to set default secondary Flash image

Hi, we are using ICX7150 switch for router feature, therefor i had use the below command for using secondary image and reload the switch in the secondary image. but, while i reboot the switch, its up by primary image only. # boot system flash Secondary yesCan you please help me to tell us how to s

Question

494

2

0

ICX 7150 C12P Switch

Hi everyone, I got a house (Lennar) and it comes with ICX 7150 C12P and I tried adding the ethernet cables to the switch so I could connect tv's and computers in different rooms to ethernet. But I'm getting 10 Mbps. How do i change the port to have actual speed to 1G-Full instead of having 10-ful

Question

101

1

0

Accepted Solution

tagging a VLAN on lag port

Hi all, I have an ICX7150 with a lag port that uplinks to a 7650. I created a new VLAN that I need to tag, so I can have this traffic flow between the two switches. When I do this, do I need to tag the vlan on the lag port, or just on the ethernet ports that make up the lag port, or tag all of

Question

132

2

0

Important Announcement

Announcements

Categories

View More