SmartZone (SZ) & Virtual SmartZone (vSZ)

SmartZone (SZ) & Virtual SmartZone (vSZ)

SmartZone (SZ) & Virtual SmartZone (vSZ)

785

  • •••
T

Accepted Solution

AP Firmware SmartZone back to ZoneDirector without reset button?

I'm preparing to upgrade our ZoneDirector to a new SmartZone 144 controller. I've tested the process of upgrading the firmware and moving a R510 using the SmartZone's ZD Migration tool. I've also manually converted the AP back to the old firmware, but I had to press the reset button on R510 to get t

Question

44

2

0

Should I use vSZ & vSZ-D on single machine?

Hey guys,I have a quick question pertaining to the two instances I listed above. I'm currently building out a server, and was wondering if it's wise to install both instances on a single VM (obviously I'd leave some cushion on specs for these to work in-sync) . I'm wanting to centralize all traffic,

Question

26

1

0

vSZ can't start service

vSZ can't start service and login https://ip local:8443

Question

41

3

0

How to downgrade dataplane SZ144-D

I want to downgrade a SZ144-D dataplane from 6.0.0.0.1331 to 5.2.2.0.317. Apparently there is no way to upload older firmware directly to the dataplane; only upgrade is available and trying to downgrade to an older version with upgrade commands leads to "Upgrade Fail". So, I wanted to try cluster

Question

24

1

0

Accepted Solution

Ruckus vSZ stuck on halting after configuration.

I installed a 6.0.0.0 vSZ on a Hyper-V, the deployment worked fine the config website starts up. After I finish the configuration via webUi the vSZ uses "halt -f -d -n" and get stucked at this point the VM is doing nothing... I was trying to install the vSZ via Shell got the same issue. I have no op

Question

32

1

0

Getting duplicate MAC error on L2 ACL when there is no duplicate

I am unable to add any MAC addresses to one of my L2 ACLs, which only has 49 addresses in it at the moment. No address can be added and no duplicate exists in the list itself already. I am able to add addresses to other ACLs, so I suspect that there is some sort of database index corruption on that

Question

38

3

0

Accepted Solution

Official Solution

Port/VLAN best Practice

Hi Everyone, I have a SZ-100 setup with a single port group setup. We have 46 APs currently and are expecting to add 30 more at another location on campus. Currently, the primary wireless LAN lives on the same VLAN as the APs and the SZ-100 (the vendor that installed the equipment set it up t

Question

127

3

0

Flagged AP status clearing

1. Hello, currently we are using VSZ-H 3.6.2 and we would like to deep dive onto access points that have flagged status in VSZ GUI. however, we can only get the status through hovering the pointer over the flagged and it will show the status. with this, is there another way to extract the reasons fo

Question

70

1

vSZ-E System Capacity

Hello everyone! I just recently started getting set up with my new Virtual SmartZone controller. I have the controller itself licensed (but I haven't applied my AP licenses yet). I'm looking under the "System Info" page, and found the total capacity listed for the cluster (1 node currently) is 10

Question

81

2

0

vSZ issues after deployment - Wireless Latency

I recently deployed a vSZ controller appliance at work.  I also have deployed thirteen R650 access points.  This system replaced a Zone Director physical appliance and five R500 access points.  The old system worked fine without issue.  Users were able to access their Horizon View desktops w

Question

185

2

Important Announcement

Announcements

Categories

View More