Joining the Community is Easy!

Our community is a great place to share and connect with other people that are passionate about the same things you are. Get your questions answered, share your ideas and feedback, get your problems solved, and give back by helping others! It only takes a minute to get started.

Get Started Today

  • Step 1: Sign Up
  • Step 2: Follow Categories

Conversations

Recent Conversations
Conversations 1 - 20 of 3769
Photo of Holger Weil
R510 - Maximum RF Power - Region Code
Hi, can you provide a list or datasheet for the R510 with the RF Power Output regarding to a region code, for example Germany? Best Regar...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of kmart
SZ300, SCG200 Comparison
Hi, Does anyone has comparison between SCG200 and SZ300? We want to know what's the new offering and its features for the SZ300. Thank ...
  • 1 me too
  • 0 replies
  • Question
Photo of Luc-SVK
Ruckus H510 antenna pattern and placement
Hello all, i got a question about Ruckus H510 wall AP. I found antenna patterns here: https://support.ruckuswireless.com/answers/00000209...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of David Liu
does Ruckus support Capwap tunnel between AP and controller?
Does Ruckus support Capwap tunnel between AP and controller?
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Menelik Yabowork
Can I use poe out on ruckus zoneflex 7762 as data in ?
Can I use poe out on ruckus zoneflex 7762 as data in ? This is because the data in can only receives power from the poe injector but does...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of prabaharan B
SWITCH Configuration
I am using CISCO SG300-10P POE model. I want to know How to do DHCP SCOPE  on this model in CLI mode. I just see steps in internet But it...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Marco Eichstetter
Unleashed AP - Suddenlty Factory Reset
Hello, i have a strange issue which happend two times now. A few weeks ago Customer told me that two Outdoor-Mesh-APs (T300 Unleashed) a...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of Ben Winslow
Log Analysis tool reference manual
Is there a reference manual that goes over all of the information that is included in the report that is generated when you upload a debu...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Skaap2.0
Ruckus AP's - Multicast UDP stream Issues ZF7363 and R500
Multicast and UDP stop streaming issues: Hi All, I've been having major issues with a Hotel/Property running ZF7363's and R500 AP's in ...
  • 1 me too
  • 6 replies
  • Question
Photo of Supporto Ice
repeater configuration on RF2942
Hi, I have a customer with 9 AP RF2942 installed. Now the customer wants to add another AP in an area not covered by signal without l...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Pamuditha Abeysekara
Creating 2- Node SCI Setup ( Master Node + Data Node)
Hi,  I have few questions about 2-Node SCI setup where we have more than 3000 APs. 1.) Do both SCI nodes (master and data) have web GUI?...
  • 1 me too
  • 3 replies
  • Question
Photo of Rakesh Gupta
Cluster out of service Alram in SZ-100, what is the cause of the issue ? any solution suggested .
Getting cluster out of service message in the SZ-100 dashboard. I know that is a critical alarm but not getting any idea how to fix this ...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Pamuditha Abeysekara
How to Protect SCI Database?
Hi all, Is there any redundancy mechanism or HA mechanism supported by SCI. Since it contains sensitive data what can we adhere to as a...
  • 1 me too
  • 5 replies
  • Question
Photo of Nnamjin Roh
What is " snapshot disk" command in VSCG for?
I found "snapshot disk" command in VSCG.  How can I use this command"  what is this command for?
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Vladimir Lavrukhin
Is there a CLI reference guide for ZF7372 AP?
I can't find anything in the technical documents section. There are several CLI guides for ZoneDirector and FlexMaster. But I'm looking f...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Daniel Beaver
Backwards migration - vSCG to ZD
I've found dozens of posts and even PDFs detailing how to easily migrate APs from a ZD to vSCG, but what about migrating them back to the...
  • 1 me too
  • 4 replies
  • Question
  • Acknowledged
Photo of Jeronimo
AP don't join to vSZ on 3.5.x.
Hi. Some APs don't join to vSZ on 3.5.x. I captured packets between Ap and SZ. It shows "encrypt alert" same as below again and again....
  • 1 me too
  • 6 replies
  • Question
Photo of Gilson Fraboni
Ruckus zd1006 System is recovered from failure
Ruckus zone director 1006 disconects all aps for no apparent reason. We analyze the logs in the menu monitor - All events / Activitties ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Rasmus Thorslund
script to turn off either 2.4 or 5Ghz?
I need to calibrate our network for spot, but in order to do so we need to disable each band while testing the other. We are running on a...
  • 1 me too
  • 1 reply
  • Question
Photo of Acacia IT
Malformed DHCP sporadically coming from clients connected via Ruckus AP, REQUEST/ACK
Looking for a little help or some ideas here. Setup: Just deployed a ZD3025 (FW: 9.12.1.0 build 148) with 16 AP's; mix of R300, T300, T3...
  • 3 me toos
  • 5 replies
  • Question
  • In Progress