icx7250 won't stack I get a "stack port e 1/2/1 has 1g speed-duplex settings" error
We have a
Brocade ICX7250 that will not stack. We atleast 40 sites with the same stack configuration. So this isn't a new setup for us.W...
Conversations
Recent Conversations
Conversations 101 - 120 of 7000
ICX Questions
Hi,I have few questions about ICX1. I want to do rollback if I didn't save manuallyin Aruba using these command alias, save, job2. I want...
T710 can't be powered on with 802.3at compatible switch
I flashed the AP to unleashed 200.8 for now. I tried two switches, both support 802.3at, one is ubnt es-8-150W , the other is
...
Wi-Fi Calling on Unleashed
First I just want to say thank you for adding this to
Unleashed! I have configured a Profile
for this and enabled it on a WLAN, but I ...
ICX 7150-24P corrupted flash?
Switch lost it's configuration after a power outage.During boot i am getting the following messages:Starting kernel ...booting with 4.4 k...
Query : Access point Should also allow Signal rejection for 3G/LTE/WiMAX in a co-Located environment
Should also allow
Signal rejection for 3G/LTE/WiMAX in a co-Located environment
Downgrade an AP without downgrading ZD1200?
Is there a way to downgrade individual APs? I tried uploading an older firmware in the "AP Patches" section and that did not do anything ...
Ruckus Unleashed slow speeds
Hi everyone, I just replaced a Draytek Wifi network with 4 Ruckus R510 acess points. The problem that I'm having is while hardwired into ...
Brocade ICX 6450 POE trunk port
Hi guys, i have questions. I have to connect the ICX 6450 POE switch through a trunk port with a cisco switch. Is it possible? Is it poss...
ICX 7450 - Unable to save configuration. Flast to Flash Error
Recently I'm having problems saving changes to an ICX 7450-24 stand alone switch (firmware 08.0.90T213):--------------------------------...
R600 unleashed dropping 2.4ghz
R600 unleashed dropping 2.4ghz connection.
Hi. I have unleashed running on 2 R600's that are wired into a switch. Mesh option is off....
Authentication Failure or event 201
I am using a radius server. sometimes I have a device that is still trying to connect using a users old password, and after trying the ba...
WiFi 6 / 802.11ax AP compare? X50 Series
I was looking at https://www.commscope.com/product-type/enterprise-networking/wireless-access-points/indoor/Compare/?ids=121604|122464|12...
What does the message "send_controller_config line: 96 Controller connecting error, errno: 2 No such file or directory" mean?
I estimate 75% of the syslog entries are made up of the message "send_controller_config line: 96 Controller connecting error, errno: 2 No...
how to enable LACP for T710 in unleashed firmware
I am new user for Ruckus APs. I have two concerns below. 1. Does unleashed firmware support LACP? 2. R710 has two eth ports, both can con...
vSZ 5.2.1 CLI Session
So two things...1. Is it expected behavior that you must log into the vSZ with the local admin account only to be able to use the CLI Se...
Hi I am getting random radio on message
2020/09/06 00:04:20 AP Radio On High Radio [5G] of AP[5FL-R-606] is ON Clear
2020/09/06 00:04:20 AP Radio On High Radio [2.4G] of AP[...
In the ssid I chose "none" to remove the password, but the ssid still has the password help me please
In the ssid I chose "none" to remove the password, but the ssid still has the password
help me please
Can I run 2 R510's off 2 Netgear switches?
I purchased a Lennar home last year and it came with an ICX7150 switch and 2 R510 AP's running Unleashed with mesh configuration. Unfortu...
Role based Access Control Policy: how to assign a dynamic VLAN based on role?
We want to assign a dynamic VLAN based on the role of a user.SSID settings: RBAC enabled, dynamic VLAN enabled, client fingerprinting ena...
Ruckus Forums
Welcome to our customer community! If you have questions to ask, problems to report, or other feedback to give, you've come to the right place. Our team does our very best to help out as fast as we can.
Curious to know more about what we do? Check out our Related links below to learn more!
Categories
View all
Related
Community Stats
-
7,386
Conversations -
12,512
Members