My MediaFlex 2811 AP Cant't Upgrade new firmware ?
My MediaFlex 2811 AP Cant't Upgrade new firmware ? My 2811 AP firmware version 3.1.1.1636, I find new version firmware is 4.1.0-15 Firmwa...
Conversations
Recent Conversations
Conversations 6061 - 6080 of 6110
Cannot connect to Internet through SSID created
Have a Verizon router passing DMZ through to a NetGear router handling DHCP.
Ruckus is behind the NetGear.
When I plug directly int...
Map view is showing MAC Addresses and not AP Name
It seems that the last 10-15 AP's installed are only showing the MAC Addresses in the Maps. Before it showed the AP Name which is much ea...
Sierra 760s modem and Ruckus wi-fi repeater compatibility
I am attempting to upgrade to a Telstra Sierra 760s modem and need a wi-fi repeater that is compatible with it. Four days wasted trying t...
802.11r / 802.11k support
Hi folks,
We're about to deploy a ruckus network at a new premises and there is a reasonable number of mobile devices there over four ...
ZF7762-S concurrent client support user limit
Has anyone knows what ́s the ZF7762-S concurrent client support user limit?
In datasheets is 256, but ZF7762-S-AC is 500.
In other mo...
Zoneplanner transmit power levels
HI there,
I am doing my first zone planner job and need to adjust my transmit power levels to the correct level.
I have found this ...
7762 PoE power usage
Whats the real world power usage of a 7762 (Not S) with the PoE disabled?
VPN between 2 office with one ZD
Im going to set up a site-to-site vpn between two offices that we have.
Is there any best practice how to arrange this?
Im need the ...
Using the Ruckus Wireless Training Portal (RWTP)
This discussion topic is on how to use the RWTP, a new learning management system for Ruckus as of August, 2013.
Please visit the RWTP...
ZF7731 IP Config Info
I have a pre provisioned ZF7731 pair. Do the root and non root devices need to have an IP on the same network to see each other? They d...
My First attemp with Zone Planner??
Hello;
I have some inquires after using ZP firs time:
1 - What is the optimum RSSI level 'Indoor' with a reasonable data rate f...
Installed 4 Stand Alone APs and Want to configure....
Hello we have installed 4 stand alone 7352 AP's without a Zone Director. Is there a way we can change the WPA2 password other than connec...
Ethernet port speed negotiation
Kicking the tires on a 7982 running 9.4 firmware. Hooked the WAP up to a Netgear GSM712 switch, but on gig-speeds both the switch and th...
Wireless between buildings
I currently have two buildings connected with fiber. I want to have these buildings connected with wireless as well as a backup route in...
DHCP problem with Ruckus 7363
Hi Everybody.
I have an 7363 and DHCP service doesn ́t assign IP addresses on wireless clients. I upgraded firmware to 9.6.0.0.267 bu...
Effect of rate-limiting on channel efficiency
Rate limiting each client increases the amount of time needed to complete data transfer (assuming the air-interface is not the bottleneck...
Port Mapping in flexmaster every time clicking the zone director
Hi,
How do i configure to redirect the flexmaster to zone director? what are the other things to check/ verify about the port mapping ...
Blocking All Local Traffic except a few IPs
I've got a WLAN that staff use with their own personal devices that is password protected. I would like to block ALL local traffic EXCEP...
Is it possible to switch a users vlan after authenticating with the hotspot?
Is it possible to have Hotspot service with with two VLANs setup ? When user initially connects to WLAN, Ruckus should put him in VLAN X,...
Ruckus Forums
Welcome to our customer community! If you have questions to ask, problems to report, or other feedback to give, you've come to the right place. Our team does our very best to help out as fast as we can.
Curious to know more about what we do? Check out our Related links below to learn more!
Categories
View all
Related
Community Stats
-
6,454
Conversations -
11,141
Members