someone can give me the signal range in open area?
 1 Post
 0 Reply Likes
Posted 4 years ago
 20 Posts
 2 Reply Likes
There is no a short answer for that. Many factor will influence in how the signal behaves even in open area.
But as an alternative you can check our support site data sheets of every AP to have a better idea
Victor,
But as an alternative you can check our support site data sheets of every AP to have a better idea
Victor,
 100 Posts
 15 Reply Likes
Hi Bong,
It is a bit complicated and reverse engineering math , when we talk about the rage/ distance covered by a radio . Basicaly the range of an AP depends on alot of factor, TX power/interference/ obstacles / reflection/ Fresnel zone (If out door) . Theroticaly we can calculate the distance/range by considering free space path loss and the EIRP.
First you need is to determine predictive/expected the EIRP of the radio/AP and what is at your client . 2nd ,receiver sensitivity of the access point and the client . Calaculation of EIRP is as follows.
EIRP= TX power set on the AP  cable loss + Antenna gain
Lets say: 15db 3db + 11 db = 23 EIRP
Once we determine the EIRP of the access point ,we can than calculate the FSPL( Free space path loss) based on distance and the frequency . Frequency plays a very important role in calculating the distance of a transmitter . 2.4 ghz give us a good range as its wavelegth is longer than 5ghz.
Here is the formula for FSPL
FSPL(dB)} = 20log{10}(d) + 20log{10}(f) + 32.45
D5 = Distance in Miles
D9 = Frequency in Mhz
Lets say FSPL = 50db at 300ft distance
Now EIRP Path loss would be the signal strengh i.e EIRPPathloss =Signal ==> 23 50 = 27
SO lets say the client's receiving sensitivity is 70 , which means , it can have the signal as low as 70 and it will work fine. So 27 is the strong signal at 300ft.
Now if you increase the distance in the formula and try to make the signal 70 or above . As client has the receiving sensitivity of 70 , it would be the range ( Distance)for this client .
I know it is too complicated at once,however if you calculate the Free Space Path Loss and EIRP, it will give you a rough idea at what distance the client will still have a good signal,and determine the coverage area.
Hope this helps
Thanks
Munish
It is a bit complicated and reverse engineering math , when we talk about the rage/ distance covered by a radio . Basicaly the range of an AP depends on alot of factor, TX power/interference/ obstacles / reflection/ Fresnel zone (If out door) . Theroticaly we can calculate the distance/range by considering free space path loss and the EIRP.
First you need is to determine predictive/expected the EIRP of the radio/AP and what is at your client . 2nd ,receiver sensitivity of the access point and the client . Calaculation of EIRP is as follows.
EIRP= TX power set on the AP  cable loss + Antenna gain
Lets say: 15db 3db + 11 db = 23 EIRP
Once we determine the EIRP of the access point ,we can than calculate the FSPL( Free space path loss) based on distance and the frequency . Frequency plays a very important role in calculating the distance of a transmitter . 2.4 ghz give us a good range as its wavelegth is longer than 5ghz.
Here is the formula for FSPL
FSPL(dB)} = 20log{10}(d) + 20log{10}(f) + 32.45
D5 = Distance in Miles
D9 = Frequency in Mhz
Lets say FSPL = 50db at 300ft distance
Now EIRP Path loss would be the signal strengh i.e EIRPPathloss =Signal ==> 23 50 = 27
SO lets say the client's receiving sensitivity is 70 , which means , it can have the signal as low as 70 and it will work fine. So 27 is the strong signal at 300ft.
Now if you increase the distance in the formula and try to make the signal 70 or above . As client has the receiving sensitivity of 70 , it would be the range ( Distance)for this client .
I know it is too complicated at once,however if you calculate the Free Space Path Loss and EIRP, it will give you a rough idea at what distance the client will still have a good signal,and determine the coverage area.
Hope this helps
Thanks
Munish
John D, AlphaDog
 499 Posts
 139 Reply Likes
It's really difficult to come up with a figure for this. Munish has a good answer for the theory of signal range, but whether or not the signal is usable for that range depends on a lot of factors (including interference from other AP's in the area), and the initial parameters depend on how you mount your AP's both in terms of orientation and nearby physical obstructions.
If you are targeting mobile devices, their dynamic orientation poses a unique challenge too around the fringe of reception. They might have okay reception until they turn away from the AP or grip their phone right on the wifi antenna, at which point their throughput plummets.
I don't have any experience with the 7363, but I have seen with the 7372 vs 7982, the better antenna array on the 7982 does give you maybe 1020% more range, but it's not a hugely noticeable difference for a large price gap. If your budget is virtually "unlimited", then the 7982 is a superior choice, but if you are trying to choose between more of (7372/7363) vs fewer 7982's, then I would absolutely recommend getting more lowercost AP's rather than relying on fewer highercost AP's to cover a larger range.
If you are targeting mobile devices, their dynamic orientation poses a unique challenge too around the fringe of reception. They might have okay reception until they turn away from the AP or grip their phone right on the wifi antenna, at which point their throughput plummets.
I don't have any experience with the 7363, but I have seen with the 7372 vs 7982, the better antenna array on the 7982 does give you maybe 1020% more range, but it's not a hugely noticeable difference for a large price gap. If your budget is virtually "unlimited", then the 7982 is a superior choice, but if you are trying to choose between more of (7372/7363) vs fewer 7982's, then I would absolutely recommend getting more lowercost AP's rather than relying on fewer highercost AP's to cover a larger range.
Related Categories

Ruckus Indoor APs
 1549 Conversations
 640 Followers