untagged a vlan on Lan2 for AP's R500, R510, R610, R710 and R720's for IPTV steaming on SZ100 Firmware Version 3.5.1.0.862

  • 1
  • Question
  • Updated 2 months ago
  • (Edited)
Hi All,

I'm busy deploying a new SZ100 on a site that has a IPTV system.

The TV's in the rooms connect directly to the AP on Lan2,

I have setup the profile under Tunnels and Ports, but i also need to disable igmp snooping and directed multicast.

Normally i would use the below commands on a ZD. What would the SZ cli commands be?

set qos eth0 igmp-snooping disable
set qos eth0 directed multicast disable


set qos eth1 igmp-snooping disable
set qos eth1 directed multicast disable

Assistance will be hugely appreciated.

TIA

Shaun


Photo of Skaap2.0

Skaap2.0

  • 23 Posts
  • 2 Reply Likes

Posted 2 months ago

  • 1
Photo of Anusha Vemula

Anusha Vemula, Employee

  • 60 Posts
  • 29 Reply Likes
Hi Shaun,

qos commands are AP specific and you can use the same commands on all APs. It does not matter if they are managed by a ZD or SZ.

Regards,
Anusha
Photo of Skaap2.0

Skaap2.0

  • 23 Posts
  • 2 Reply Likes
How would i run these commands on the SZ to all ap’s or Ap-models. Ive tried going into the sz via ssh, but wasn’t able to figureout how to send this to all the specific models.
Photo of Anusha Vemula

Anusha Vemula, Employee

  • 60 Posts
  • 29 Reply Likes
For SZ managed APs, we use the AP CLI script.

Paste the below commands in a notepad and save it in .txt file.

Syntax :

fw_version= <AP firmware version>
model=all 
<Command> 

Example :

fw_version=3.6.1.0.354
model=all 
set qos eth0 igmp-snooping disable

Upload the file under Administration>Diagnostic > AP CLI script and you can execute the script per zone.

We cannot run the script on specific AP models as it can be executed only at Zone level. You can keep the same model APs in one Zone and execute the script on it.

- Anusha


Photo of Skaap2.0

Skaap2.0

  • 23 Posts
  • 2 Reply Likes
Hi Anusha

I'm getting this error when trying to upload the .txt file

Unable to upload the AP CLI script to the controller. Reason: com.ruckuswireless.wsg.domain.diagnostics.exception.InvalidAPCLIScriptFileException: Wrong AP script syntax.

Ideas?
Photo of Skaap2.0

Skaap2.0

  • 23 Posts
  • 2 Reply Likes
Thank you. Appreciate the guidances.
Photo of Anusha Vemula

Anusha Vemula, Employee

  • 60 Posts
  • 29 Reply Likes
It has to be AP firmware version and there should not be any space between the lines.

-Anusha
Photo of Skaap2.0

Skaap2.0

  • 23 Posts
  • 2 Reply Likes
I have tried that aswell

see below


fw_version=3.5.1.0.1010

model=all

set qos eth0 igmp-snooping disable

Photo of Skaap2.0

Skaap2.0

  • 23 Posts
  • 2 Reply Likes
Got it working, My Mac .txt files didnt want to upload. created them on windows and all good.
Photo of Anusha Vemula

Anusha Vemula, Employee

  • 60 Posts
  • 29 Reply Likes
Good to hear that.

-Anusha
Photo of Robert Lowe

Robert Lowe

  • 201 Posts
  • 47 Reply Likes
for reference, here is a link to the Ruckus Hospitality Best Practices Guide for SZ. It includes details of how to disable directed multicast amongst other best practices. https://ruckuswireless.egnyte.com/dl/LGcbBk7wAP?mkt_tok=eyJpIjoiWmpKbFpEazJOMkV6WlRZeCIsInQiOiJUcUdyWGdPTTR1eTdPVmdKdDBOZ3BVVUQ1a0ZqTE1SVGhOdGtcL3l4XC9DWWg0MzVkbmNYYjlaZmI2QjJjenJXT0ZrOGVzRFNCODNCRTAwVVM1S0VzTExRPT0ifQ%3D%3D