License Activation
we upload -2X10G-LIC-POD , Before we installed two 10G license and activated only one port.. now we are not able to activate the second ...
Simon
Joined on November 30, 2017
17
Likes received
0
Conversations posted
53
Replies posted
28
Conversations followed
Conversations
Conversations 1 - 20 of 28
load balancing mode of a LAG
I need to check the load balancing mode of the lags on the physical switches (ICX6610, 08.0.30t) facing our esxi cluster. On the cluster ...
Switches using Router code vs Switch code and decision making
Hi all, When an ICX switch is on router code, is every packet a forwarding decision even if the ICX device is on a switched circuit on l...
How to perform a hard reset on icx 7450?
How to perform a hard reset on icx 7450? I tried this procedure but it did not work: 1 Remove power from the switch. 2 Press and h...
failed to connect ICX 7150 to SZ
Hi,i have installed an ICX7150-C12-2X1G POE 12-port - Version:10.1.15T225and i am trying to connect it to my Smartzone vSZ-H - 5.1.1.0.59...
General PoE Data: Firmware Version 00.0.0 Build 000
POE Failure. General PoE Data:
+++++++++++++++++
Firmware
Version
----------------
00.0.0 Build 000
How should I go ...
Which ICX Release is Suggested?
For the ICX 7xxx series, which release is suggested? Should we be sticking with 08.0.80 builds (i.e. upgrading from 08.0.80d to 08.0.80e...
SmartZone
hi Guys, how are you? my question is silly and simple. i just wanted to know what is smart zone?
What does Cold start mean?
I have a switch where in the ICX 7450 where its system up time were back to 0... How can I identify if it is user triggered or if the swi...
How to access a locked out ICX 7250 with SPR08090ufi? console aaa enabled, no local users
Hello everyone, I've done a stupid thing, it seems.I did erase the startup config on an ICX 7250 with aaa console enabled. Result seems t...
Can Ruckus ICX 7150-C12P act as a router and do NAT?
I have a new Ruckus ICX 7150-C12P switch. I’m wondering if I can connect it directly to my ISP’s modem and let it act both as a DHCP serv...
supportsave fcx with scp
Hi all, is there a way to make a supportsave with sftp or scp. HW: Stackable FCX648S SW: Version 08.0.01bT7f3Kind regards, Reinhold.
How do you configure an ICX-7450 with the ICX7400-SERVICE-MOD IPSec Module?
I have an ICX-7450 48-Port PoE switch with the ICX7400-SERVICE-MOD IPSec hardware module installed and firmware upgraded to the 08.0.80 r...
which version should I use for ICX ?
Hi there,I have two questions regarding to version string.I've listed sample below.- Ruckus ICX FastIron 08.0.80b (GA)- Ruckus ICX FastIr...
ICX7150 trying to access Ruckus Wireless Device Registrar
Hi,ICX 7150-24 version 08.0.80dT211.There
are continuous attempts to access 35.160.244.72 and 52.34.241.9 over
443/tcp via Management...
ICX7150 no output show inline power
Hi AllWe have an ICX7150-24P-4X1G POE 24-port, with 10 R510 AP's. All the AP's are down but switch is up leading to me a POE issue. S...
Brocade ICX 6610 switch High CPU and drops RDP and internet connections. This happens about every two months otherwise works great.
Brocade ICX 6610 switch High CPU
Dynamic VLAN 802.1X Switchport Behavior with Unmanaged Switch Downlinked
Does anyone know what happens to the VLAN assignment of a DVLAN 802.1X wired port when connected it's downlinked to an unmanaged switch w...
ICX products.. BFD used to be supported on these products and now it looks to be AWOL. ????
BFD feature on ICX missing in Ver 8 code stream.
Do Ruckus switch required any specification or special type of media converter?
My customer using ICX7150-24P as Access switch and core switch, the connection between Core and access switch are fiber optic and UTP cab...