POE module of ICX 7450 24P is not working ?
I tried to enable POE on ICX 7450-24P, but it doesn't show any output.Core#show po poe inline power information ...
Jijo Panangat
Joined on August 23, 2018
25
Likes received
0
Conversations posted
65
Replies posted
41
Conversations followed
Conversations
Conversations 1 - 20 of 41
what is procedure for upgrading licences
I have yet a licences for SFP moduls.Currently I have only two sfp port activate with exists licence and I would like to activete mor...
ICX 7450-24 AAA not operational
Can't login using AAA radius to a ICX 7450-24. It displays the error when enter credentials and press return/enter: "AAA: udp listner no...
Can I have some layer 3 ports and some layer 2 ports on a 7150?
I am looking for a command that would work the same as 'no switchport' on a cisco. Assume the 7150 has a newer version of the routing s...
which recommendation to upgrade icx 7250 to version 08.0.90d (SPS08090d.bin)?
After upgrading to SPS08090d.bin, the operating system did not start.
what is the recommendation, because the current version 8.0.30p
Firmware recovery Fastlron FESX424HF + 2XG
I mistakenly formatted the Fastlron FESX424HF + 2XGPlease tell me how to restore the firmware.And also where to get the firmware.FEX-Boot...
ICX-7650 Core Latency
HI, i am connecting my pc to a edge switch vlan and pinging to the core switch ip then i m getting latency in pinging. There is distrib...
ip multicast
Hi , I'm configuring the multicast on Rukcus Switch for the first time, I used to do that in HP switches.I used to activate fastleave on ...
New LAG showing LACP-Blocked
Setting up a new 4 ports LAG for a newSAN.
I basically copied
the LAG settings from the current production one.
(still new to this...
ICX 7150: Not letting me create a Router-Interface
HELP!!!I've been trying to create a vlan with its own dhcp server, however for some reason my switch is not letting me create a router-in...
Disable Should Also Shut Power Down to the Port
When a switch port is set to "disable" the port should also shut down power. The current behavior stops traffic though the end point is s...
Modify Traffic Policy
Hi all,This may be a silly question, but I can't seem to find the answer for it.How does one modify a traffic policy? I understand I wou...
failed to connect ICX 7150 to SZ
Hi,i have installed an ICX7150-C12-2X1G POE 12-port - Version:10.1.15T225and i am trying to connect it to my Smartzone vSZ-H - 5.1.1.0.59...
Public custom VLAN not working on Fiber internet ICX 6610
I will be decommissioning and removing copper connection in couple of weeks. Instead of doing cutover migration using eth 0. I decided to...
Uploading Image for Ruckus 7150
I tried to upload image for ICX7150-C12-POE and it was succesfulBut when i show version, I saw information as belowBYT-Ruckus-Spare#show ...
Why can't I enable multicast on ICX 7250
We are using the ICX 7250 switch in combination with data diodes and for that reason we need multicast to be enabled. But when I enable t...
Layer 3 Switch ICX 7150 : PIM configuration
Hi,I used to configure router PIM on HP switches to route multicast between VLANs, I need to know how can i do that on Ruckus switches?DT...
I cant my Connect ICX 7250 to ISP modem access
I can't access the internet from my vlan's but can access all PC inside in VLAN's
can not connect ICX 7250-24 with Opendaylight oxygen controller
Hello Everyone,I have ICX 7250-24 switch and ODL oxygen version. I have connected the ethernet interface 1/1/1 to the ODL controller. th...
Customizing web authentication on ICX7250
Hello everybody,I am working on a web authentication page for an ICX7250.I have already customized top, bottom, title, login, button and ...