Conversations
Conversations 1 - 20 of 31
Hi everyone. I am new on Ruckus community and I am having problem to access web interface of my smartzone 100 controller. After a reboot ...
How to force device to use same AP all the time. We have 2 above each other
ACL Access Point
2.4Ghz Latency goes high suddenly
Hi all,I have an total ruckus environment ( ZD100 + Ruckus 610 APs) into 2 of my offices.On both offices, i have a problem on the 2.4ghz ...
A poor throughput performance standalone AP with NAT forwarding.
I have tested throughput test with NAT forwarding for Ruckus AP and some vender APs.On Nat-forwarding, Aruba(IAP mode)and Samsung AP(stan...
updated zd1200 to fw 9.13.3.0.157 , r600 ap's at local site updated ok but remotes sites fail
WE have two zd1200's and 5 sites, the main site has the Zd's and 25 r600 aps, all connected by vpn and each of 5 remote sites has 5 r600 ...
Ruckus ZD1200 Reports
Hi!About reort of ZD1200, refer internet traffic trend, its only possible to take a 24h report? I need a mouth report for study and upgra...
Client Isolation MAC OS (Apple) Failure - SZ300
Gentlemen, I have a packet loss and connection failure problem when I enable the "client isolation" feature on my SZ300. Being very speci...
AP FLAGGED STATUS
We detected most of our AP with Flagged status. This status happened randomly with random APs. The Flagged type is AP health high connect...
Access Point R510 doesn't receive an ip address from Windows DHCP server
Hi, I connected a R510 Access Point with a switch but the R510 doesn't receive an ip address from the Windows DHCP Server. With a notbook...
SZ300 fw 5.1.x with many errors (WiFi Event)
Friends,We manage an event with the SZ300 fw 5.1. An event with 106 AP's, and we've seen some differences that are not yet clear if I sho...
Can I determine approximate date of manufacture based on MAC address?
We found a few Ruckus AP's broadcasting similar names to my client's corporate SSID, but they may be on different floors of our building ...
DHCP server icx 7750
After upgrading icx 7750 from 08.0.40 to 08.0.80 My multiple DHCP servers is malfunctioning. A PC can get a lease, but a iPhone or IP p...
Settings to maximize performance 2 x R610 running unleashed
I am running 2 R610 with the unleashed firmware. I am looking for the best settings to get the greatest bandwidth through the devices. ...
SmartRedundancy with 3 ZD5000 controllers
Friends,I know that ZD's are EOL, but we need a plan of action in case there is a failure in a website/ZONE (RJ or DF), the fear of recov...
Tunneling mode
Hi Everyone. Newbie here. I have zone director 3050 and zf AP. AP’s are located in different locations (branch offices) (routed). ZD is a...
Problems with Roaming
Hello there,hope someone could help me. We serve a large WLAN of a hotel and getting problems with clients when they roam. the problem is...
SmartRedundancy with multible Sites
Hello, i have one Main-Site and two Remote-Sites. Right now, there is a ZD1205 on the Main-Site. Is it possible to use SmartRedudundancy...
Outdoor AP placement guideline
We're planning an outdoor coverage area of about 10 acres (455,000 sq ft). This is mostly open space with gardens. Ideally, we would li...
SCG200 - Signal coverage does not appear
Dear, I am with a SCG200 version 3.5.1.0.862, and since I am responsible for the RF of a big event, I configured my MAP with all access p...
SCG200 - How can I block traffic through DataPlane SCG-D1
How can I block traffic by Data Plane1Friends,We are working with SCG200, and have set up a new Datapla. I would like to know how do I bl...