AP remains disconnected on the ZD on WAN
Hi I'm a newbie and my boss asked me to deal with APs and ZD. We have our ZD in a datacenter, connected to WAN. My job is to reinstall s...
Darrel Rhodes
Joined on October 5, 2018
20
Likes received
0
Conversations posted
54
Replies posted
31
Conversations followed
Conversations
Conversations 1 - 20 of 31
Cannot connect on second and other SSID Unleashed R310
Hello, I got 5 R310 and spreading 3 SSID's over al the AP's but one of them is showing the SSID's but when I try to connect the client do...
Connectivity issues after firmware upgrade from 200.5.x to 200.6.x
We have a small Unleashed network of 5 R500 AP's that is covering our company Wi-Fi network needs. The setup is using VLAN's, but is quit...
[ASK] R600 Radio 5Ghz is down
Dear All Forum Members, I have Ruckus R600 with unleashed firmware. The problem is Radio 5Ghz is down. What should I do for bring up Rad...
Zone Director 1100 firmware upgrade path to 9.10.2
Hi,I need to upgrade a Zone Director 1100 from firmware: 9.8.3.0 build 14 to 9.10.2.0.63 (MR2 Refresh4). I cannot find a suitable upgrad...
MTBF for R310, R510 and T310
Hello, i am looking for documentation where MTBF is mentioned for products R310, R510 and T310. Is there anything available?
R610 and R510 Can't connect.
I know very little about networking but I needed better wifi for my nightclub. I watched a few videos on the unleashed and really liked ...
Error on ZD 1200 and r500 aps not joining.
I have a property I just had to reset the ZD 1200 on. 24 of the APS came in and worked fine. 24 others had the cloud based firmware on th...
H510 - SSIDs isolated to individual switch ports
I've seen similar questions asked, but this is a bit of a unique setup. I want to be able have 4 SSIDs, we'll say 1-4, SSID 1 is isolate...
M510 and Zone configuration (SmartZone)
If you try to move an M510 to a Zone with a non-tunnel or non-dhcp/nat SSIDin a WG, you will end up with the error message, that this is ...
Can an R720 run at full power by decreasing antennas on PoE+, and what is the range difference between PoE+ and PoH?
I'm looking at the spec sheets for the R720 and it states that on PoE the 2.4Ghz radio is in 1x4 mode at 18dbm per chain, at PoE+ it is i...
RUCKUS R510 - APs
I have 2 R510, how do I configure the two R510 as one Access Point with same SSID. And it will just load balance the the traffic. Thanks.
Does ruckus supports AD certificate for Authentication Instead of Radius Server authentication??
In Small business environment the customer don't go for Radius server for authentication. So can you explain me does Ruckus support Acti...
Auto Cell Sizing between R510 and R720
I test Auto Cell Sizing between R510 and R720. They are both controlled by vSZ 5.0.0.0.675.On controller I see that R510 and R720 are nei...
2.4Ghz migration to 5Ghz unexpected !
Hello I have just migrated approx. 50 access points to 5Ghz only and shut down 2.4Ghz. The reason was to avoid the high levels of 2.4Ghz ...
Connect AP ( R510) to Virtual SmartZone - Essentials 3.6 using wireless only ( without cables conected to the network)
Connect APs ( R510) to Virtual SmartZone - Essentials 3.6 using wireless only ( without cables connected to the network) - I`m planning...
R510: Import MAC address list and limitations
I'm setting up a new R510. I have 126 MAC addresses in the allow list on my old hardware. I can't see how to import that list on the R510...
Is it possible to use guest access without ssl cert. for ZD1200 9.13.3.041 firmware?
Hi, I would like to know is there anyway to assign guest access with using SSL cert. Because, when I setup guest access with no authe...
Can't figure out how to Configre Zoneflex R610
I recently purchased a few ZoneFlex R610 AP's after a brief test run with the R310. For some reason I can't get the R610 to phone home a...
R720 upload slow compared to R710 (Controlled by ZoneDirector 1200 10.1.1.0 build 55)
Hi Situation (in basic/short - maybe little too basic): 4 WLAN's deployed. About 20AP's (different models). R710 controlled by ZD 1200...