Conversations
Conversations 1 - 20 of 34
Evening all, I'm hoping you can help me out. I've spent a good 4 or 5 hours trying to google my way out of this one, but I haven't gotte...
Fastiron Edge X648-prem
Hello. There is a problem. I have a Fastiron Edge X648-prem switch (ver. 07.4.01T3e5), I want to install a 2x10G board on it, took it fro...
ICX6610 invalid input when trying to creating ve interface
I'm getting the error invalid input when trying to create ve interface. Is there any changes in command for creating this ve interface? o...
ICX7450 - ports up and down
Hello, I have a bunch of Brocade switches ICX 7450 (firmware 08.0.3k). The problem is that I have a lot of logs from flapping ports. The ...
How to display the MAC learned by the interface in log and syslog?
Well, I need the ICX 7150 switches to display the MAC address of the device when it's plugged into the switch. I can visualize this with ...
error invalid input when trying to create ve interface
I'm getting the error invalid input when trying to create ve interfaceFirmware version : SPR08061cI have created a VLAN , added an untag...
ICX 08.0.80ca PSA - Missing bootloader in Zip
If you are updating to 08.0.80ca, please note that there is no bootloader included. I'm pretty sure if you try to boot with the old pre ...
How do you show the arp table on a ICX 7450 running 08.0.30q ?
How do you show the arp table on a ICX 7450 running 08.0.30q ? Our previous version: 07.3.00j that ran on the FCX 648 you could simply is...
Uplink ports explained
Hello, So sorry for what could be a very basic question but I'm starting to learn about networking and Ruckus. I've got an ICX 7150 24P...
updating FWS firmware using TFTP
I have a Brocade FWS648G switch which I received as RMA. I have assigned an IP to switch and same range ip address to the PC.I am able to...
ping from config menu
Hi, I have FCX648S How can I do ping from configuration menu Quite hassle if have to exit from config menu to do ping tq
ICX7250 L3 DUAL ISP Load Balance?
Is this possible on the ICX platform? I'm assuming no, as NAT and other L3 services aren't yet available, but are planned.
TDR cable diagnostics only works on master switch in a stack
Trying to avoid opening a case unless I have to. We have noticed that the TDR cable diagnostics works on the master switch in the stack,...
multiple sflow destinations
When defining multiple sflow destinations, does the switch round robin between the two or does it send the same data to all configured de...
ICX 6450 PoE Allocation Issue
I have two ICX 6450 24P switches at my garage. They run PoE for VoIP, Access Control and Cameras. I had a report that the cameras were no...
Foundry Switch Firmware Upgrade Order
I have some Foundry FESX424F-PREM switches. They are running version 3.1. I also have IronWare 7.2. Can I jump from 3.1 to 7.2 or are the...
Foundry Switch Jumbo Frames Support
I have some Foundry FESX424F-PREM switches running version 3.1. I see from various places online that jumbo frames are supported. In the...
Is any kown Issue with ICX6450 stacking
Hi All, I'm using ICX6450-48 port 2-stacked switch in a my local environment, all stack ports are 10G. I have configured stack ports on...
ICX7750 randomly rebooted. Standby took over
ICX7750 randomly rebooted. Standby took over. Anyway to see what caused the reboot? Also what is the recommended version to go to on t...
Broadcast limiting vs an unmanaged switch with a loop
I'm working with a 7150-24 port switch in a test environment. I'm looking at how to address potential loops for connected un-managed swi...