1843 zfcu2n inline large

ZoneFlex Outdoor APs

Conversations

Recent Conversations
Conversations 1 - 15 of 450
Photo of Daniel Baker
ZD1200 Location
I'm a complete Ruckus newbie.  I have purchased a ZD1200 and 2 ZoneFlex APs.  I am the local phone company/ISP.  We will be placing the A...
  • 1 me too
  • 5 replies
  • Question
  • Acknowledged
Photo of Demetris Demetriou
802.11r SQL Roaming
Hello, on a T300 AP where the max number of concurrent users connected is 500 (based on datasheet) i created 4 different SSIDs. I know t...
  • 2 me toos
  • 3 replies
  • Question
Photo of Keith Hoover
Is there a limit to the number of dynamic vlans a single SSID can support?
I am considering a project that may have up to 200 different vlans on one SSID, is that supported?
  • 1 me too
  • 2 replies
  • Question
Photo of treebert
7762 outdoor APs - 5.15 - 5.25 GHz band (channels 36 to 48) output power
We have ZoneFlex 7762 APs purchased before 2014. We would like to take advantage of the 2014 FCC rule change that allows outdoor usage of...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Andreas Georgiou
T300 & T310 antenna gain and TX sensitivity
Hello, I would just like to know what is the relation between the antenna gain of an AP and Beamflex+. From information I have gathered f...
  • 1 me too
  • 2 replies
  • Question
Photo of Robert Wrenn
P300 SpeedFlex test , is it accurate?
Using a P300 bridge about a quarter of a mile apart to connect a ZoneDirector 1106 to six 7782 APs. We were expecting at least 500Mbps u...
  • 1 me too
  • 6 replies
  • Question
Photo of mehdi koraichi
T3OO AP bandwith
Hi all, I wanted to know how to calcualte the bandiwith of an AP like T3OO, i'm getting the rx and tx values via SNMP and based on those ...
  • 1 me too
  • 0 replies
  • Question
Photo of pasan jayarathna
is it possible to enable SNMP on Wireless AP and get it via the network and monitor via PRTG?
is it possible to enable SNMP on Wireless AP and get it via the network and monitor via PRTG?
  • 1 me too
  • 1 reply
  • Question
Photo of Jong Ha KIM
when using T710 AP's PoE Out port, I Must used power injector?
I'm studing for outdoor AP... T710's PoE Out port is compared to other APs (when installation busstop, Kiosk, etc..) but i can't find Con...
  • 1 me too
  • 2 replies
  • Question
Photo of Shrug
Can anyone point me to docs for configuring a T301e?
Can anyone point me to docs for configuring a T301e? The AP is up and running under my Unleashed Master.  I want to enable the external 5...
  • 1 me too
  • 3 replies
  • Question
Photo of Jim Philopena
WPA 2 Enterprise
We're looking for a solution to provide better security for our wireless network.  We of course wished to use WPA-2 Enterprise with a cer...
  • 1 me too
  • 1 reply
  • Question
Photo of Ruzanna Zohrabyan
ZF7762-S doesn't connect to the ZoneDirector 1200
Hello dear colleagues, I have a ZF7762 with firmware version 9.7.0.0.220 and Ruckus Wireless ZoneDirector ZD1200 with firmware version 9....
  • 1 me too
  • 4 replies
  • Question
Photo of Fabio Giudici
Backup Bridge with spanning tree or trunk
a few years ago I installed a point-to-point bridge with two 7731 antennas, now the client asked me to create an additional bridge to...
  • 1 me too
  • 3 replies
  • Question
Photo of Lefhoko Radisaka
I get the "bad firmware header magic" error message when i try to upgrade T300 AP from 100.x to 104.x
  • 1 me too
  • 4 replies
  • Question
  • Acknowledged
Photo of Lefhoko Radisaka
add T300 AP that is running 100.x code to the existing SZ 100 Controller
How do i add T300 AP that is running 100.x code to the existing SZ 100 Controller because it is not recognizing the "set scg ip " command?
  • 1 me too
  • 3 replies
  • Question