1843 vw1k9k inline large

SmartCell Insight (SCI)

Conversations

Recent Conversations
Conversations 1 - 15 of 67
Photo of Jeronimo
Spark Master goes down after upgrading to SCI 5.0.
Atfter upgrading SCI from 3.x to 5.0, Spark Master goes down. How do I recover it? How do i check which deamon is problem? If I can c...
  • 1 me too
  • 3 replies
  • Question
Photo of Jeronimo
SCI shows us "Your Spark cluster was unable to accept a job submission".
Hi Team. Out SCI for demo shows us Your Spark cluster (Spark master IP: xxx.xxx.xxx.xxx) was unable to accept a job submission. How do ...
  • 1 me too
  • 1 reply
  • Question
Photo of gpmpa
How to Increase SCI secondary Disk
Hi,  Can I increase the SCI secondary disk size after deployment without losing any data?  Thanks gpmpa
  • 1 me too
  • 2 replies
  • Question
Photo of RS
Weekly WiFi Health Report Generation
Hi Team, We are using Ruckus SZ100 with about 48 APs (R700).We have had WiFi issues in the building and we have been adjusting bss min ra...
  • 1 me too
  • 2 replies
  • Question
Photo of Thembelani Ncube
Applications data reporting on SCG 200 v3.4
Hello there, Is application data reporting supported on SCG? Below is the current version of our SCG planes and our SCI version 3.6.0 - ...
  • 1 me too
  • 3 replies
  • Question
Photo of AndiT
Why SCI doesn't show information in the "Application" tab?
I installed the SCI 3.5 and did the integration with a ZD with firmware version 10. I got all the client, APs information but I can't see...
  • 1 me too
  • 3 replies
  • Question
Photo of marius.steyl
SCI Spark Master
Our SCI 3.6.0 recently gave this error "Your Spark cluster (Spark master IP: x.x.x.x) was unable to accept a job submission. I cant seem...
  • 1 me too
  • 3 replies
  • Question
Photo of Barry Hermkens
Ruckus SCI 3.5.0 setting > system not visible, but loading icion (fresh install)
After installing VM SCI 3.5.0  i want add a controller under "setting > system" , there is no +Add button, only a loading icon, that does...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Allan Grohe
Wi-Fi Alliance Announces New Wi-Fi Security Features Available in 2018
On January 8th 2018, Wi-Fi Alliance® announced its intent to enhance and add new features to Wi-Fi Protected Access®, building on Wi-Fi C...
  • 1 me too
  • 0 replies
  • Announcement
Photo of gpmpa
Maximum no of SCI Data nodes per SCI Cluster
What is the maximum no of Data nodes configurable in SCI cluster.  According to the installation guide I do see it's limited at 4 data no...
  • 1 me too
  • 1 reply
  • Question
Photo of Marko Teklic
Severe flaw in WPA2 - cracked
when can we expect to see update for this https://arstechnica.com/information-technology/2017/10/severe-flaw-in-wpa2-protocol-leaves-wi-f...
  • 34 me toos
  • 50 replies
  • Question
  • Answered
Photo of Jeronimo
Why does ZD show this msg for SCI?
Hi. I have configured setting for SCI 3.x and ZD(9.13.x). But ZD is shown below message sa "but login sci failed. I have configure s...
  • 1 me too
  • 2 replies
  • Question
Photo of kmart
can we add user roles for SCI? we only see admin roles now. Our client wants to share data for view only roles.
User Roles for SCI
  • 1 me too
  • 1 reply
  • Question
Photo of gpmpa
SCI 3.2 granularity
Hi  Can I select the 3-min, 15-min granularity while setting up SCI or after deployment according to requirement. I don't see any option ...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of gpmpa
Creating 2- Node SCI Setup ( Master Node + Data Node)
Hi,  I have few questions about 2-Node SCI setup where we have more than 3000 APs. 1.) Do both SCI nodes (master and data) have web GUI?...
  • 1 me too
  • 3 replies
  • Question