30895 3bkff0 inline large

ICX Campus Switches and General Switching Questions

Conversations

Recent Conversations
Conversations 1 - 15 of 91
Photo of TJR
protocol error, doesn't start with scp!
in lieu of any actual ansible modules, i am trying to make raw ssh commands work to an ICX 7750 switch, but even "ssh <ip> "show version"...
  • 1 me too
  • 1 reply
  • Question
  • Acknowledged
Photo of Robert Lowe
Moving between Router & Switch Codes
Hi All, Can anyone tell me what would happen to my config if i upgraded a switch from router code to switch code? I have a switch stack a...
  • 1 me too
  • 1 reply
  • Question
Photo of Robert Lowe
Removing a switch from an existing stack
Is there a procedure to follow to remove switches from an existing stack?
  • 1 me too
  • 2 replies
  • Question
Photo of Robert Lowe
dot1x & MAC auth using RADIUS with Router Code
Hi All,We're implementing dot1x and MAC auth on 7150 stack (08.0.80) running router code (basic). We've configured dot1x and MAC auth to ...
  • 1 me too
  • 0 replies
  • Question
Photo of Fernando Flórez
Add second ICX switch
First of all, great product and great community! Thank you! So today I went out and bought another ICX switch (7150-c12p) and would like...
  • 1 me too
  • 14 replies
  • Question
Photo of Muthu S
how to configure the dot1x authentication in icx 7250 switch
we are using flat network in our environment.NPS server 2012 - ip 172.128.252.10/16 - I have created nps profile key admin123 Switch Ip -...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Alvis
How do you show the arp table on a ICX 7450 running 08.0.30q ?
How do you show the arp table on a ICX 7450 running 08.0.30q ? Our previous version: 07.3.00j that ran on the FCX 648 you could simply is...
  • 1 me too
  • 3 replies
  • Question
Photo of Fernando Flórez
Avoid client changes on the switch routing
Hello, so today as part of my learning I tried to connect a wi-fi router to my network. After a little while all the vlan was down. Looke...
  • 1 me too
  • 2 replies
  • Question
Photo of Fernando Flórez
PCs under VLAN can't reach internet but SW can
I'm in a phase where all vlans work correctly and I'm trying to use the uplink ports to reach my router. Here are the relevant parts of ...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Skaap2.0
H320 not being picked up by SZ100
Hi All,I'm busy deploying a new SZ 100 with H320 Access Points on a New Ruckus ICX7450 and ICX 7150 network, I'm having a issues with the...
  • 1 me too
  • 1 reply
  • Question
Photo of Clayton Tavernier
ICX 7750 routing table confuses me
We have a 7750 as our core router and remotes sites with either a 7750 or 7450 as their router.  The configurations were set up by an out...
  • 1 me too
  • 8 replies
  • Question
Photo of Fernando Flórez
Uplink ports explained
Hello, So sorry for what could be a very basic question but I'm starting to learn about networking and Ruckus. I've got an ICX 7150 24P...
  • 1 me too
  • 12 replies
  • Question
  • Acknowledged
Photo of luciano vieira da silva
How to monitor traffic of vlans individually from switch icx7450
Hi Colleagues.I have an icx-7450 switch, and snmp has been configured for monitormanet, I can monitor memory, CPU, temperature, etc. But ...
  • 1 me too
  • 1 reply
  • Question
Photo of nbctcp
Automatically backup config to scp or tftp when "write mem"
In Cisco, I can do that using thesearchivepath scp://root:[email protected]/$hwrite-memory How to achieve the same in FCX648S ver 8.0.30 tq
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Pradeep sonawne
i am looking for script through i can take weekly backup of configuration.
Hi All,I hope that you are doing well...i am new in Brocade ICX family switches.i have one small query if any one can help me, it will be...
  • 1 me too
  • 5 replies
  • Question
  • Answered