30895 3bkff0 inline large

ICX Campus Switches and General Switching Questions

Conversations

Recent Conversations
Conversations 1 - 15 of 127
Photo of Allyson Pereira
Ruckus ICX 7750 IPV6 hardware support forwarding
Hello dears,The ICX 7750 switches supports IPv6 in hardware, in order to provide wire-rate forwarding for IPv6 packets? Thank you!
  • 1 me too
  • 1 reply
  • Question
Photo of Allyson Pereira
ICX 7750 traffic shaping
The ICX switches family supports QoS Traffic Shaping feature? If yes:. The switch can be perform actions to the packets that exceeds the ...
  • 1 me too
  • 2 replies
  • Question
Photo of Martin Fox
Brocade loop protect issues
Would it be possible for Ruckus to implement a similar loop protect to HP please? This seems to be work on a mac address level - which we...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Graeme Earl
Brocade ICX 6610 switch High CPU possible mcast or mcast_fwd?
We have set of stack switches that get a very high CPU usage which drops RDP connections and slow everything down. 
  • 1 me too
  • 1 reply
  • Question
Photo of Graeme Earl
Brocade ICX 6610 switch High CPU and drops RDP and internet connections. This happens about every two months otherwise works great.
Brocade ICX 6610 switch High CPU
  • 1 me too
  • 1 reply
  • Question
Photo of Maslivets Jaroslav
Fastiron Edge X648-prem
Hello. There is a problem. I have a Fastiron Edge X648-prem switch (ver. 07.4.01T3e5), I want to install a 2x10G board on it, took it fro...
  • 1 me too
  • 6 replies
  • Question
Photo of Scott Oram
R510 AP and ICX 7150 - APs shutdown and do not power back on
Here is my setup: Comporium Zipstream Gigabit fiber main box gets Ethernet from junction box in garage. The comporium box hands out dhcp...
  • 1 me too
  • 11 replies
  • Question
Photo of Hasan Shukri Zakaria
ICX6610 invalid input when trying to creating ve interface
I'm getting the error invalid input when trying to create ve interface. Is there any changes in command for creating this ve interface? o...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Eric Markow
Dynamic VLAN 802.1X Switchport Behavior with Unmanaged Switch Downlinked
Does anyone know what happens to the VLAN assignment of a DVLAN 802.1X wired port when connected it's downlinked to an unmanaged switch w...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Shane Waldrop
ICX6610-48P - PoE Error: Device 0/1 failed to start on PoE module
Upon boot-up (cold or reload) the switch is failing to initialize the PoE module.  Is there anything I can try to resolve this?ICX6610-48...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of Duane Guilbeau
Required boot and os firmware combinations for ICX6450
Are there recommended/required combinations for the boot and os firmware on the ICX6450's?  I've got a few different versions across our ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Angel Sixto
How to add a backup default route???
I have 2 layer 3 ICX6610 switches configured in a stack that is acting as our core switch for our enterprise. We have primary (unreliab...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Ruslan
RADIUS ACL attributes
Can`t find how to assign ACL with Access-Accept RADIUS response and what attributes to use.Want to know how to assign ACL via sending id ...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Brian Hiatt
Configuring ICX 6430-24 for media streaming?
Hi Folks,I'm very new at this, and Ethernet is not in my "day job".  I just got my first managed switch, a used/surplus ICX6430-24.  I us...
  • 1 me too
  • 5 replies
  • Question
Photo of Laura Pineiro
ICX7450 - ports up and down
Hello, I have a bunch of Brocade switches ICX 7450 (firmware 08.0.3k). The problem is that I have a lot of logs from flapping ports. The ...
  • 1 me too
  • 6 replies
  • Question