R

2 Messages

 • 

130 Points

Sun, Dec 5, 2021 2:27 AM

Upgrade ZD3050

Hi,

i have network with ZD3050 and AP 7352

my current controller version 9.5.0.0 build 156

is there last safe firmware for ZD3050 and AP 7352 to upgrade ?

Accepted Solution

Official Rep

 • 

170 Messages

 • 

2.2K Points

2 m ago

Hi @ryan_ardhi 

You can upgrade your controller ZD3k to build code 10.1.2 which will still support AP ZF7352. These AP model's are not supported from 10.2 and above. Below is the article that would help you with upgrade path which is required while upgrade to keep the current config of system intact.

https://support.ruckuswireless.com/articles/000001845

Note : Always take the backup while upgrade and post upgrade of one code of controller wait for the AP's to update the new code too and then go to next code.

Best Regards

Vineet

2 Messages

 • 

130 Points

@vineet_nejawala 

thank you

i'll try

2 Messages

 • 

70 Points

@vineet_nejawala

hello...

is it save to upgrading?

 

Official Rep

 • 

170 Messages

 • 

2.2K Points

@syaiful_umar

I am unable to identify your existing version of ZD? You need to be on below version before upgrading to 10.1 to keep your config intact. If you are not on any of below code the ZD would go to factory default setting (you will lose all configuration on ZD).

The following release builds can be directly upgraded to this version:
• 9.13.0.0.232 (9.13 GA)
• 9.13.1.0.11 (9.13 MR1)
• 9.13.1.0.26 (9.13 MR1 Refresh)
• 9.13.2.0.33 (9.13 MR2)
• 9.13.3.0.22 (9.13 MR3)
• 9.13.3.0.41 (9.13 MR3 Refresh)
• 9.13.3.0.106 (9.13 MR3 Refresh 2)
• 9.13.3.0.121 (9.13 MR3 Refresh 3)
• 9.13.3.0.133 (9.13 MR3 Refresh 4)
• 9.13.3.0.145 (9.13 MR3 Refresh 5)
• 9.13.3.0.157 (9.13 MR3 Refresh 6)
• 9.13.3.0.164 (9.13 MR3 Refresh 7)
• 10.0.0.0.1424 (10.0 GA)
• 10.0.1.0.17 (10.0 MR1)
• 10.0.1.0.35 (10.0 MR1 Refresh)
• 10.0.1.0.44 (10.0 MR1 Refresh 2)
• 10.0.1.0.61 (10.0 MR1 Refresh 3)
• 10.0.1.0.83 (10.0 MR1 Refresh 4)
• 10.0.1.0.88 (10.0 MR1 Refresh 5)
• 10.0.1.0.90 (10.0 MR1 Refresh 6)
• 10.0.1.0.93 (10.0 MR1 Refresh 7)
• 10.0.1.0.123 (10.0 MR1 Refresh 8)
• 10.0.1.0.133 (10.0 MR1 Refresh 9) 

Best Regards

Vineet

2 Messages

 • 

70 Points

@vineet_nejawala

Hi Vineet, 

my ZD Version  :  Version= 9.5.0.0 build 156

OK, it will be reset to factory default, can I restore with backup data from a version before?

because my account was unable to download on a lower version of the firmware. "That file is only available to Premium Support users."

thanks, 
 

Official Rep

 • 

170 Messages

 • 

2.2K Points

Hi  @syaiful_umar

Unfortunately answer would be no. You can restore config backup taken from 9.5 to only 9.5 code controller and not on 10.x or any other. 

Best Regards

Vineet

Important Announcement