Official

Accepted

Unanswered

Advanced Filters

Search Results (522)

Activity

Accepted Solution

ICX 7150 c12p - AP with multiple VLANs

Hi, I've not been able to find an answer for this. I have multiple VLANs on being tagged by my Access Point (R610 for now, will get more later): default (50) default-iot(200) The AP is connected to an 7150 (PoE), and when I try to tag multiple VLANs to the same port I'm told that is not po

Question

 • Switches

22

2

0

Incorrect ECMP behavior

I've got a 7150 stack running the 09.0.00 'routing' firmware (yes, I know it's not GA, but with 08.x.x I had serious problems with IPv6 routing). I have OSPF enabled and there are two connected nodes which publish the same destination via OSPF (anycast). Here's the current OSPF route information

Question

 • Switches

12

0

0

illegal class reported by PD

hi I've connected some (17) Ubiquiti WAPs to an ICX7150-ZP48. some WAPs arent loading (all connected with direct patch cables in the lab). it seems to be randomly not always the same WAP. "sh inline power" output shows this error" illegal class reported by PD all WAP are the same mode

Question

 • Switches

47

3

0

How to log in the ICX 6450-24p by Out-of-band management interface

Hello My friend: I have an ICX 6450-24P switch,but now i can't log in by the console management interface,There is no problem with the interface settings,So I suspect the interface is broken, I know there are other ways  to log in,such as  out-of-band management、Web and so on,I want to l

Question

 • Switches

22

1

0

0x43 illegal class reported by PD

I have 2 Ruckus ICX7450-48P switches that are having similar issues with POE. I'm receiving "illegal class reported by PD". The lights on the POE devices blink on and off continuously. So far I've tried 4 different Unifi Access Points and one IP Phone Both switches are on the latest GA and runnin

Question

 • Switches

20

5

0

POE firmware issue "Loss of sync with controller in slot 1"

hello community i have an issue with POE firmware on my ICX-7150-ZP48. I've upgraded the switch to version SPS08095d using UFI file. the switch was upgraded and using the 08095d image, but the POE firmware isn't installed. "sh inline power details" output shows that the firmware ver is 00.0.0

Question

 • Switches

19

4

0

Rucus ICX7850-48

Good afternoon.Now 4 switches ICX7850-48FS installed in the stack.Two more stages of adding switches are planned.There is a desire deploy Campus Fabric"Ruckus FastIron Campus Fabric Configuration Guide, 08.0.92"Two questionsIs it possible to use ICX7850 the quality of the CB?Is it possible to use IC

Question

 • Switches

28

1

0

Hardware solution for Dual WAN gateway to gateway VPN

Hello, I am looking to connect 2 geographically distant (> 5 miles) sites. Both sites have dual WAN fail over, and dynamic IP's from each ISP. I am looking for a hardware (or general solution) recommendation to allow a secure connection between both sites that could withstand a WAN fail ov

Question

 • Switches

30

1

0

Lennar Connected Home ICX 7150-c12p R510 AP Setup

I purchased a Lennar home with a ICX 7150 and R510 AP.  The wifi signal was broadcasting the Lennar assigned SSID and the ConfigureME-XXXX.  I downloaded the android app and connected to the ConfigureME net and followed the steps.  That's where I'm stuck.  I don't see the SSID I assigned during setu

Question

 • 

Answered

 • Switches

11.4K

22

ICX stack stops responding to IPv6 Neighbor Solicitations

I'm working on replacing the core of my network with a stack of 7150-C12P units running the layer 3 image. So far things have been working pretty well, but I've run into a problem. I'm running the 08.0.95caT213 release. Specifically, I have one interface setup for route-only traffic to the existing

Question

 • Switches

32

2

0

Ruckus ICX 7450 false alert for BGP peering

We have a pair of Ruckus ICX 7450 switches that are running a router software that has multiple BGP peerings established and working without any issues, these switches also have SNMP service enabled which triggers any events on the device and send that alert to monitoring systems. We keep receiving

Question

 • Switches

11

0

0

Accepted Solution

Official Solution

MCT with LR Transceivers

Hi, as I have not found a clear answer from the MCT Documents. Is it possible to use LR Transceivers for the ICL Connection of an MCT instead of DAC Cables? I was unable to find a definitive source for it. I expect it to work, as it does work for Stacking and for MCT only a static LAG is requir

Question

 • Switches

30

2

Accepted Solution

ICX 7150 FIRMWARE QUESTION

Hi everyone, I have an ICX 7150 running version 08.0.95 routing version on both flash partitions (primary and secondary).  So, Can I change it to or upgrade it to SPS (L2/Switch) version only?

Question

 • Switches

51

1

Accepted Solution

Stacking two ICX 7550

Hi, I'm planning to stack two CS ICX 7550 for redundancy links to Access switches , my question is, it will be necessary to have duplicate DAC cable for redundancy or just one cable is enough ?

Question

 • Switches

46

3

Official Solution

Ruckus icx 7150 fails to start(CRITICAL: Failed to do SIL Init, error: -1)

Ruckus icx 7150 fails to start. The following is an error message ICX7150-24 Copper (Non-POE), P1SYS CPLD VER: 0x0 Released Ver: 0x27 Crashkernel Disableddevice 0 offset 0xbfe00, size 0x200device 0 offset 0x0, size 0xc0000Enter 'b' to stop at boot monitor:  0device 0 offset 0x0, size 0xc0000B

Question

 • Switches

51

1

ICX7150-C12P 10G SFP+ license

Hi there, I just purchased an open-box ICX7150-C12P, but it turns out that there isn't a 10G license on there. How do I go about upgrading this license? Currently: show license is showing Unit License Name L3 Premium Port Speed Upgrade Speed Ports MACsec 1 2X1G No

Question

 • Switches

48

2

I have an ICX 7150-C12P and the PoE has switched off.

I have an ICX 7150-C12P. The power was out for several hours and when it came back on the PoE wasn't active. I have done the factory reset about a dozen times and I can't get it back. I've read all these complex instructions on finding IP address, using a terminal prompt etc etc etc. Unfortunately a

Question

 • 

Answered

 • Switches

3.6K

29

7150 no POE to APs

Why is my switch not powering the access points?

Question

 • Switches

49

4

What code should I run on my ICX? Check the Target Path Selection Guide!

Hey All, Have you ever wondered what code Ruckus officially recommends you run on your ICX? You are in luck. We have a Target Path Selection Guide that is a great starting point for most customers. While this document will not cover every single scenario or customer, it is what you should referen

RUCKUS Self-Help

 • Switches

41

0

Official Solution

Is there a Ruckus Virtual Machine available to learn the ICX FastIron 09.0 software?

Would like to test a lab before deploying in production before our switches arrive as a GNS3 or VM for labbing. Can you provide guidance on what options are available?

Question

 • Switches

47

1