Official

Accepted

Unanswered

Advanced Filters

Search Results (533)

Activity
ICX7250P POE Daughterboard Replacement?

HiI have obtained a ICX7250P with 08.0.95ba Firmware The switch works normally, but the POE Module Reports:- Severe Error - Module Failed to Init. I have reloaded the Boot, Image and POE Firmware with no effect. The switch works normally, the POE module fails to initialise. On closer internal ins

Question

 • Switches

26

1

0

SSH Stops after 2 weeks

We have multiple ICX 7750 and 7450 in our DCs. Randomly we get SSH failing after approx 2 to 4 weeks. To fix we have to go to DC and console onto device and apply crypto zeroise then crypto generate CLI commands. This is impacting and time consuming. Any ideas why it is doing this? Code version is 8

Question

 • Switches

407

6

How do I check for ECMP with ebgp?

Hi all, I've enabled ip load sharing globally as well as maximum-paths in ebgp itself.  Checking my route table, I see only one route to my destination.  If I disable the ports, the secondary route does insert itself in the table.  Is this expected behavior for ECMP over ebgp?&nb

Question

 • Switches

28

3

0

Switch not getting configuration from SmartZone

We are using a SmartZone 100 to manage our APs and are now installing ICX 7650 switches to run multi-gig APs. These are the first Ruckus switches we have and I am having issues with them getting the configuration from the SZ. SZ is on version 5.2.1.0.515 Switch version is TNS08095a I have setup swi

Question

 • Switches

187

1

0

Cloud Support for 7250/7450 Series

We have 16 7250/7450 switches in our network. None are stacked, all spread throughout campus. We also have 40 R710 APs on a ZD1200 controller. We are evaluating migrating this to Ruckus Cloud. For the APs, we will either keep the 710s or possibly migrate to WiFi6 APs (all or some). This part is c

Question

 • Switches

38

2

0

ICX Switches - Integrate with Ruckus Cloud platform?

Can the ICX switches fully integrate with Ruckus Cloud?I have been using the Ruckus cloud platform and wanted to know if the ICX switches could be managed via the cloud portal?I have found some info about ZD integration but don't seem to be able to find any info relating to the Cloud. ThanksPhil

Question

 • Switches

173

2

ICX Upgrade HTTP Request Failed

Hi, I'm trying to upgrade via https with command copy https flash The file is no issue when I'm opened with browser and download directly to computer, but at switch I got error message HTTP Request Failed for Request ID: 1. Response Code: 404 Right now I'm using firmware SPR08092d and want to u

Question

 • Switches

89

6

0

There is any password restriction for ssh in ICX7150/7250 switches?

We have a new standard from our Project Managers regarding users passwords in ICX7150/7250 Switches. They want us to use something like !P@ssw0rd! (with some characters between exclamation mark) but is not working for SSH. They works with the ! as enable password.I removed the first ! and it worked.

Question

 • Switches

44

1

Accepted Solution

Ruckus branded software on Brocade branded ICX 7xxx hardware?

It's such a long story about why, but I have a pair or Brocade ICX 7450-24 switches that were never deployed that I'm just rolling out now. I'd love to update the firmware first, but it appears Ruckus has taken over Brocade. Show version provides, among other things: SW: Version 08.0.20T213. So tha

Question

 • Switches

81

10

0

ICX6450-48 showing Error: I2C access failed for device 0x2f

Hello, This is a NOS switch that I just purchased. I updated the FW using the configuration file (in 08030h, so FI08030h_Manifest.txt) through the console. All went well and I reset the switch. Problems started when I moved the switch from the bench to the rack. The above message shows up in the co

Question

 • Switches

96

6

0

Official Solution

How do you disable fanless mode on a ICX 7150?

I am new to working with Ruckus switches. We purchased one and I am trying it out as well as it's features.  I enabled fanless mode and am wondering if there is a command to disable it without factory defaulting the switch.  Any advice is appreciated.

Question

 • Switches

114

2

0

ICX7150-C08P SFP Uplink problem

Hi guys! I have a partner configuring 7150-C08P (running 8.0.91t) connect to 7150-24P (.90d). It works if using RJ45 ports to connect. When using SFP 1G, the C08P end is up, -24P end is down (same result with all port). They use a 7150-12P to test with 7150-24P and everything is fine. Any suggestio

Question

 • Switches

286

2

0

Routing Public LAN (/28 block) over Peer to Peer (/29 Block) Gateway Connection

Comcast ran an EDI circuit (Metro Fiber) to our office. They originally gave us. /29 block but we needed additional public addresses. I am able to assign any of the useable addresses from the /29 block and use the gateway that is in the same subnet without any issues. What is new for me and where I

Question

 • Switches

25

0

0

Accepted Solution

Non-blocking throughput?

What is the Non-blocking throughput of the ICX7150-24P (or any ICX switch)? Can't find this anywhere. The data sheet mentions Non-blocking throughput, but that's it. I assume that means that the switches have a Non-blocking design, but hoping to confirm that.  Thank you.

Question

 • Switches

95

1

0

ICX7250 , port security: mac address is refreshed on interface and not moved...

Hi, since last december I have this security warning on our ICX 7250 switches where port security is enabled, its happening randomly on some ports.It's not a "violation", but a "refreshed" ?!?Example of today:W:Security: Port Security secure MAC address xxxx.xxxx.9c91 is refreshed on interface ether

Question

 • Switches

78

1

ICX 7150 Switch Layer 2

Hi, I have a new Layer 2 ICX 7150 switch and I want to connect it to 6 access points Ruckus R550. what I want to ask is how to configure the syntax to connect the switch to the access point, because here I am familiar with Cisco's device settings. Here is the configuration I want to plan to do: #c

Question

 • Switches

97

1

0

Problem routing public lan out over peer to peer up block with gateway

Issue routing public lan up block to peer to peer block with gateway

Question

 • Switches

25

3

0

Accepted Solution

stacking over copper ICX 7250

hello All, can we do a stacking if we connect copper transceiver to uplink port on ICX7250-48P-2X10G ??  

Question

 • Switches

104

2

0

stackwise virtual

Good afternoon Ruckus forum Nice to greet you, I have a specific question about the technology that Cisco handles called virtual stackwise, in RUCKUS we have something similar? Also consider which switch models we can perform virtual stacking on. I appreciate the support

Question

 • Switches

58

1

0

Does ICX 7250s support SFP+ from other vendor such Aruba

Does ICX 7250s support  SFP+ from other vendor such Aruba 

Question

 • Switches

111

2

0