Skip to main content

25 Messages

 • 

420 Points

Tue, Sep 8, 2020 2:11 AM

Answered

unleashed r310

Hello good evening, my question is the steps to follow to change the firmware from the r310 model to stand alone mode to fimware unleashed and once I make the change to unleashed mode, I can manage my network from my cell phone and in the same way the steps to follow to register my ap, I would greatly appreciate your response, greetings

Responses

246 Messages

 • 

4.2K Points

3 months ago

Hi CHAVA,

For upgrading the AP to Unleashed version: 200.7.10.202.118

1. What is the current firmware version of the AP?
2. If it is running on ZD or vSZ firmware then, factory reset the AP >> load the the below standalone version 110 on the AP.
https://support.ruckuswireless.com/software/2431-zoneflex-solo-access-point-110-0-0-0-2005-ga-softwa...
3. We can upgrade from the GUI itself.
4. Once the AP is upgraded, load the below Unleashed version on the AP.
5. https://support.ruckuswireless.com/software/2556-ruckus-unleashed-ap-200-7-10-202-118-ga-refresh4-so...

For Managing the Unleashed from Mobile:
Please refer the below link and check the section "Enabling Mobile App Remote Management" and "Generating an Unleashed ID".
https://support.ruckuswireless.com/documents/2599-ruckus-unleashed-200-7-ga-user-guide/download


I hope this helps.

6 Messages

 • 

100 Points

2 months ago

Dear Sanjay, I have the same issue but I have done as you requested above and it was not successful.  My R310 is currently on software 110.0.0.0.2005  .  It is not letting me upgrade to the next file linked in point 5 above.

6 Messages

 • 

100 Points

2 months ago

Also I just tried an older version (R310_200.6.10.1.310) and received error message: 

Upgrade/Downgrade from FSI to UI is not allowed.



246 Messages

 • 

4.2K Points

Hi Ayoub,

Can you help me with the below command output from the AP?
"fw show all"

You might have to type "ap-mode" if the CLI prompt is "ruckus#"

6 Messages

 • 

100 Points

Sanjay, thanks, but can you explain to me where i need to go and type those commands?

6 Messages

 • 

100 Points

To be clear also, I have been accessing the web UI.

Employee

 • 

599 Messages

 • 

10K Points

Hi Ayoub,

SSH into the AP using putty application or any terminal app, and then run the command.

Regards,
Syamantak Omer

Regards,

Syamantak Omer

6 Messages

 • 

100 Points

rkscli: fw show all

ipaddr:

file: R500_110.0.0.0.2005.bl7

size: 10985472

MD5 : CFE08D288A3A9C85212208506FF652F6

type: 0

local_file

-------------------------------------

current primary boot image is Image1

---------------

Magic:        RCKS

next_image:   0x130000

invalid:      0

hdr_len:      160

compression:  l7

load_address: 0x80080000

entry_point:  0x80307210

timestamp:    Tue Feb 25 20:35:58 2020

binl7_len:    10985312

hdr_version:  4

hdr_cksum:    0xFD08

version:      110.0.0.0.2005    ( 110.0.0.0.2005 )

MD5:          CFE08D288A3A9C85212208506FF652F6

product:      zf7752    (0)

architecture: 1

chipset:      3

board_type:   0

board_class:  3

customer:

Image Sign Type: Fully Signed Image(FSI).

---------------

Magic:        RCKS

next_image:   0x130000

invalid:      0

hdr_len:      160

compression:  l7

load_address: 0x80080000

entry_point:  0x8030B420

timestamp:    Wed Jun 13 13:02:24 2018

binl7_len:    23377756

hdr_version:  4

hdr_cksum:    0x71D5

version:      200.6.10.1.310    ( 200.6.10.1.310 )

MD5:          8ECDBC4FE1CBCC324F95D8958258B8AD

product:      zf7752    (0)

architecture: 1

chipset:      3

board_type:   0

board_class:  3

customer:

Image Sign Type: Intermediate Signed Image(ISI).

Tail start:   0x164af60

OK

rkscli: