Skip to main content

1 Message

 • 

70 Points

Wed, Sep 30, 2015 2:18 PM

Ruckus ZoneFlex R500 Dual-Band 802.11abgn/ac AP query

I'm led to believe the  Ruckus ZoneFlex R500 Dual-Band 802.11abgn/ac access points is only able push out 40MHz when 3 access points are in place. 

Can anyone confirm this?

Responses

48 Messages

 • 

884 Points

5 years ago

Not sure if this is what you're referring to, but there are only two (non-DFS) 80Mhz 5Ghz channels available, so if you had THREE APs in close-enough proximity to each other than you need a discreet channel for each, you wouldn't be able to do it with 80Mhz channels (because you only have two) and would have to use 40Mhz (where you have four available non-DFS channels.)

But this is an issue with ALL 5Ghz ac APs, not specific to Ruckus R500 (or any other Ruckus AP), so not sure if that's what you were getting at... I'm not aware that the R500 has any special limitations regarding channel width that the other Rxx series don't, other than performance and antenna patterns.

90 Messages

 • 

1.2K Points

5 years ago

Interesting, however, if i understand correctly, the UK would not have this 'issue' due to us having DFS channels available to use?

48 Messages

 • 

884 Points

5 years ago

The issue with DFS channels exists everywhere... we here in the states are "allowed" to use them, as well, but they come with some pretty ugly consequences... First, not all clients can understand and use the DFS channels, so if you have an AP on one, you could be preventing a sizeable chunk of your user base (particularly mobile) from even seeing said AP. Second, DFS is a radar-avoidance system, so IF the AP is using a "clear" DFS channel THEN does another scan and discovers the channel is no longer useable (because it detected radar now in use), it will get off that frequency and choose another one... but depending on the system/AP, this process can last anywhere from 30 seconds to 30 minutes... during which the AP cannot service clients.

All that said, there are only 8 (20Mhz), 4 (40Mhz), 2 (80 Mhz), or one (160Mhz wave 2 ac) that are "guaranteed" to be available for use outside of DFS here in the US. I personally wouldn't let my system use the DFS channels unless density was the #1 driving factor (think stadium) AND the wifi was not mission-critical.

I'm not really informed on how wifi works in the UK, but here's a good paper on it http://bowdennetworks.co.uk/downloads/5GHz%20in%20the%20UK%20White%20Paper%20v2.pdf

90 Messages

 • 

1.2K Points

5 years ago

Thanks Jim, quite a good read, although i did skim through it a bit.

Strange thing is, i am currently connected to Ch128 on my Macbook, but the paper says this channel shouldn't be available, so i'm assuming things have changed a little since it was written.

2 Messages

 • 

70 Points

5 years ago

comment faire pour que le R500 soit utilise en AP et SM

2 Messages

 • 

70 Points

5 years ago

I want to use two Ruckus R500 ,one to be AP the second SM at 10 mille for internet connexion

Champion

 • 

556 Messages

 • 

10.5K Points

5 years ago

Either way, it's still not true that the R500 can only use 40MHz channels if there's 3 of them. You can use overlapping 80MHz channels or even the same channel if you really want. Co-channel interference can be evil, but it also might not be the end of the world, especially if your deployment is not high density.