Documentation Downloads Knowledge How-To Hub Forums Cases Assets Warranty
Skip to main content
leo_chung_fsn1vgp4fksgb

6 Messages

 • 

150 Points

Sun, May 19, 2019 3:08 PM

Answered

How to enable R610 Port 2 and configure as Link Aggregation on Ruckus-Unleashed?

Dear all,

Does anyone can help to enable the Port 2 on R610 (picture as below) and how to use it as Link Aggregation?  Thanks a lot!

Question

 • 

Updated 

9 months ago

76

5

Responses

ankush_ankush

Employee

 • 

92 Messages

 • 

2.1K Points

2 years ago

Hi Leo,

Please refer to following article on instructions on how to configure LACP.
https://support.ruckuswireless.com/articles/000006007

You can also refer to the AP admin Guide for details. Instructs are on page#115:
https://support.ruckuswireless.com/documents/2404-ruckus-indoor-ap-110-0-user-guide

Please ensure that AP is powered using 802.3at PoE+ for it to enable the 2nd eth.

Regards,
-Ankush



0

leo_chung_fsn1vgp4fksgb

6 Messages

 • 

150 Points

2 years ago

Hi Ankish,

Thanks for your reply, but I cannot find the AP admin Guide from the link you provide https://support.ruckuswireless.com/documents/2404-ruckus-indoor-ap-110-0-user-guide and I also cannot search the AP admin Guide on Ruckus R610.  So would you please help to capture the instruction from the Guide or tell me the directly download link?

Also, does any way can enable LACP from GUI (graphical user interface) because I don't really know configure from comment line.

MANY THANKS AGAIN!

Best regards,
Kevin

1

0

ankush_ankush

Employee

 • 

92 Messages

 • 

2.1K Points

Hi Leo,

You have to login to your support portal account to see the User Guide. I hope you have an account.

Regards,
-Ankush

Like

2 years ago

0

leo_chung_fsn1vgp4fksgb

6 Messages

 • 

150 Points

2 years ago

Hi Ankush,

Surely, I have the support portal account but my problem is cannot find the AP admin Guide.  Please see below:



Also, would you please tell me "does any way can enable LACP from GUI (graphical user interface)"?  Because I don't really know configure from comment line.

Thanks again!

Regards,
Kevin

0

0

ankush_ankush

Employee

 • 

92 Messages

 • 

2.1K Points

2 years ago

Hi Leo,

Admin and UserGuide are same. Here is the direct link to download:
https://support.ruckuswireless.com/documents/2404-ruckus-indoor-ap-110-0-user-guide/download

The LACP configuration is only available on CLI and if you are having trouble following instructions, please Contact our Ruckus support team.

Regards,
-Ankush

0

0

sebastiao_paulo

7 Messages

 • 

234 Points

9 months ago

Hi am getting same problem after my ZD damaged, i can't find options to enable port 2

Sebastiao Paulo Antonio 

1

0

syamantak_omer

Official Rep

 • 

722 Messages

 • 

11.3K Points

Hi Sebastian,

By default none of the AP ports are blocked or disabled (from configuration point).

As long as AP gets 802.3at or at+ power from switch, both the ports will be operational. If AP gets 802.3af power, second port and USB port will be disabled.

To check power mode, run below command from AP CLI.

get power-mode

To force AP from Auto power to at power, run below command

set power-mode at

If AP is managed by ZD or any other controller, try changing the AP zone or AP group specific AP model settings and choose manual power over auto and set it to at.

Regards,
Syamantak Omer

Regards,

Syamantak Omer

Like

9 months ago

Was this helpful?