K

28 Messages

 • 

520 Points

Mon, Oct 18, 2021 11:05 PM

Ruckus ICX7150 C08 TFTP Upgrade

Hello,

I'm trying to upgrade the software from 08.0.91 to a newer version, however I'm having trouble doing so. I tried the copy command, but no luck. It's almost as if copy tftp isn't working for some strange reason. 

I figured the only option was TFTP, as this model doesn't have a USB port. But any ideas on how to proceed with this upgrade? Current output: 

SSH@ICX7150-C08P Switch#show ver
  Copyright (c) Ruckus Networks, Inc. All rights reserved.
    UNIT 1: compiled on Jun  6 2019 at 20:57:00 labeled as SPS08091
      (28774816 bytes) from Primary SPS08091.bin (Non-UFI)
        SW: Version 08.0.91T211
      Compressed Primary Boot Code size = 786944, Version:10.1.16T225 (mnz10116)
       Compiled on Sat May 25 10:09:26 2019

  HW: ICX7150-C08-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C08-2X1G POE 8-port Management Module
      Serial  #:FMF3845Q09R
      Software Package: BASE_SOFT_PACKAGE
      P-ASIC  0: type B160, rev 11  Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2x1GF 2-port 2G Module
==========================================================================
 1000 MHz ARM processor ARMv7 88 MHz bus
 8192 KB boot flash memory
 2048 MB code flash memory
 1024 MB DRAM
STACKID 1  system uptime is 3 day(s) 35 minute(s) 51 second(s)
The system started at 00:16:17 GMT+00 Thu Jan 01 1970

The system : started=factory reset   reloaded=by "factory reset"

======================================================================================
===============       WARNING: FI image is not booted from UFI!!!      ===============
======  Please download UFI image and reboot the system for full functionality  ======
======================================================================================

copy tftp startup-config

doesn't seem to want to work either. are these commands available in the .92 version? 

27 Messages

 • 

410 Points

1 m ago

What error do you get from the console when you try and tftp?

your post doesn’t say anything about it. 

can you ping your tftp server?

kristphr

28 Messages

 • 

520 Points

@corey_costello it only states "Incomplete command." when entering the command. 

I can't ping the tftp server (not on the same network yet). 

27 Messages

 • 

410 Points

@kristphr you have to put in the whole command. 

Do a “copy tftp ?” and you’ll see the options. 

it has to be on a network that can reach your tftp server. 

33 Messages

 • 

344 Points

1 m ago

You can also reference the upgrade guide for the complete commands required and options available for upgrading.

For example here is the 08.0.91 upgrade guide: https://support.ruckuswireless.com/documents/2878-fastiron-08-0-91-ga-software-upgrade-guide 


11 Messages

 • 

210 Points

1 m ago

Your list attempt of "copy tftp startup-config" will not upgrade the switch.  That will only attempt to copy a configuration file to the startup-config name.  And that is not a complete command in of itself.

The command you will need is

copy tftp flash <ip.address> <new firmware name> [primary|secondary]

1) where <ip.address> is, of course your accessible tftp server

2) <new firmware name> is the file image that you are upgrading to

3) [primary|secondary] one or the other, depending upon your upgrade plans.

That is the basic.  But there are other items to consider, so make sure to read the upgrade notes for the newer firmware.

Important Announcement