ICX 7150 48P - Ports turned off

Question

Good morningI have 2 ICX 7150 48P switches in stack.Image version SPS08080dBoot version mnz10114POE version icx7xxx_poe_02.1.0.b002In both switches the 1/1/1 to 1/1/8 ports are turned off.If I attack an AP the POE turns on the AP but does not pass the link.In any case, the 8-port LEDs do not light up.It can depend on thisBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while 'bcm_port_mdix_set' is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while 'bcm_port_mdix_set' is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while 'bcm_port_mdix_set' is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while 'bcm_port_mdix_set' is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while 'bcm_port_mdix_set' is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while 'bcm_port_mdix_set' is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while 'bcm_port_mdix_set' is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while 'bcm_port_mdix_set' is Feature unavailableWhat can I do?

vincent_felisaz · Answer

Hello Giorgio

You have two issues, configuration and LED.

For the LED you must use the STATUS button on the front of the ICX to change the behaviorof the LED. If you press several times the STATUS button, you can go to PoE and see if there are some ports with active PoE.

With the version 8.0.80 on the ICX 7150 you can independently enable Data or PoE on a port. To check if both are started you can use the following commands for each port:
- show inline power 1/1/1
--> check for Admin State: ON or OFF
- show interface brief ethernet 1/1/1
--> check for Link: UP or DOWN or DISABLE

To activate/deactivate PoE on a port, go to the configuration port:
- configure terminal
- interface ethernet 1/1/1 to 1/1/8
--> To disable PoE on these ports, use
- no inline power
--> To enable PoE, use
- inline power

To enable/shutdown a port, go to the configuration port:
- configure terminal
- interface ethernet 1/1/1 to 1/1/8
--> To shut Data on these ports, use
- disable
--> To enable Data, use
- no disable

Hope this help
Cheers
Vince

giorgio_sacchi · Answer

I tried to do it this but it does not change anythingIn addition I continue to have those 8 errors, can be tied to the 8 ports that give me problems?The range 1/1/9 to 1/1/48 works fine

vincent_felisaz · Answer

Giorgio,it seems there is currently a case opened on the same issue (maybe it's yours). It needs to check for physical layer (cable, port, ...) as the error is related to the MDI feature. FYI older similar cases were closed with a RMA. Vince

giorgio_sacchi

ICX 7150 48P - Ports turned off

Responses

vincent_felisaz

giorgio_sacchi

tsotne_khutsishvili

giorgio_sacchi

tsotne_khutsishvili

vincent_felisaz

Was this helpful?