Hey all - if videos aren't your thing I'll give you the dirt real quick. Starting November 12th I'm going to start a live stream on Twitch covering RU
Welcome to our new customer and partner community!
All data and content migrated successfully from the old to the new community platform, includin
We have some great content that’s been published, but not announced individually. So instead of blasting you with individual announcements I thought
Is it possible to manage VLANs on build in switch ports of H510 access point???
4 years ago
Last response by
6 hours ago
• Products & Services
When an H510 is running in unleashed mode and acting as master, there seem to be no options in the configuration interface to configure its 4 Ethernet
3 years ago
My R310 doesn't have 5g signal, but the signal light is normal
I've tried all the available firmware, but the problem still exists
Can you help me fin
4 days ago
Everything had been working fine until I had to replace the modem, same ISP.
I did hard resets; both with the reset button, an using putty. &
2 days ago
12 hours ago
Cluster controller fw - 126.96.36.199.405
Thu Jan 7 05:15:45 2021 0 day 01:05:17 970 rsmd_func cubic m
6 days ago
14 hours ago
I need a broken R710 to replace my case. Mine is broken. Do you know how/where I can buy a shell or do you have a not working unit yoursel
20 hours ago
We have an R600 AP that suddenly could not discover the ZoneDirector.
Doing a diagnostic Ping in the AP's Web GUI shows that it cannot ping t
a day ago
How do i create VLANS in ICX Network, I have ICX7450 as the core-switch and the ICX7150 on the IDF side.
Seeing multiple alerts with these reasons: last disconnected reason [AP Restart : application reboot] last disconnected reason [Change State Resp
Hello, I found an old post regarding this from 2013 which said there was no support.
Has there been any change since then for Zero-IT auto config supp
All, I am hoping I can get some help/advice. Thanks for reading.
Here's my setup:
AT&T Fiber (BGW210-700) router --> Ruckus ICX-C12P --> 3
2 months ago
I've enabled ip load sharing globally as well as maximum-paths in ebgp itself.
Checking my route table, I see only one route to my de
7 days ago
I just installed my first home Ruckus Wifi network. Still learning and trying to troubleshoot. I have 2 R550s one main and the other client AP. I w
5 days ago
3 days ago
We are using a SmartZone 100 to manage our APs and are now installing ICX 7650 switches to run multi-gig APs. These are the first Ruckus switches we
We would like to use 3rd part iDP (Okta, OneLogin, etc.) for admin authentication.This will allow to apply security controls to the admin interface.
2 years ago
The R510 AP's have a choice of performing band balancing between 2.4ghz and 5.0ghz but it asks you define the db value. Now what are some good values
Only 5G is unstable, connection is lost or SSID is not visible
Does it stabilize if I leave it for a while after installation?
Since upgrading to 188.8.131.52.302 we have been getting several oddities, one of which is two alarms:Authentication Server [172.23.0.110] not reachable fr
a year ago
We have 16 7250/7450 switches in our network. None are stacked, all spread throughout campus.
We also have 40 R710 APs on a ZD1200 controller.
Any recommendation for a gigabit router to connect R550 Aps? This is for basic home use. Essentially need gigabit speed, firewall, DHCP.
I read a lot
19 days ago
Welcome to our customer community! If you have questions to ask, problems to report, or other feedback to give, you've come to the right place. Our team does our very best to help out as fast as we can.
Curious to know more about what we do? Check out our Related Links below to learn more!
Total Posts with Accepted Solutions