Config::Wireless::Country Code - How to set Australia?

Mar 20, 2008 6:49am

starkey 4 post(s)

Any idea how I can set Australia as the country code?
Running Firmware:

Active SW ###
SW Version: 4.2.0.0.132

Mar 21, 2008 4:16am

csannedhi Administrator 71 post(s)

Go to Configuration -> Wireless -> Common tab. You should see Country Code dropdown menu to set it to Australia.

Mar 25, 2008 2:47am

starkey 4 post(s)

That dropdown menu is set to United States and the field is locked so I cannot change it. I am logging in on the super login. Is there another login I should know about?

So far I have:
Tried admin login.
Tried super login.
Reset to factory defaults.
Tried admin and super login.
Upgraded Firmeware to latest version, reset to factory defaults.
Tried admin and super login.
Tried super login on SSH connection with “set countrycode AU” and error given is “You are not allowed to change the country code”.

Any more suggestions?

Mar 25, 2008 5:54am

csannedhi Administrator 71 post(s)

If you are in US, you will get an AP with that particular country type. US customers are not allowed to change the country code because of FCC regulations.

If you are in AU, you should check with your store to find out how you received a unit with US country settings.

Aug 28, 2008 2:14am

Zoran 7 post(s)

Starkey, is you AP managed via ZoneDiroctor? If yes, hard reset your AP, plug in with your PC via Cat5 (network cable), log in to AP (defaulty IP should be 192.168.0.1) and then you should be able to change any settings.
I’m in AUS and did get the Ruckus gear from US, and did not have problems to change the settings.

Regards
Zoran

Sep 18, 2008 5:48am

starkey 4 post(s)

Thanks Zoran, but it was not that simple. I ended up following csannedhi’s advice and contacting my supplier, who in turn got me in touch with a Ruckus support tech in Hong Kong, who talked me through changing the country code via Telnet, after I had flashed another firmware. :)

Ruckus Wireless Forums

Config::Wireless::Country Code - How to set Australia?

Voices

Mar 20, 2008 6:49am starkey 4 post(s)	Any idea how I can set Australia as the country code? Running Firmware: Active SW ### SW Version: 4.2.0.0.132

Mar 21, 2008 4:16am csannedhi Administrator 71 post(s)	Go to Configuration -> Wireless -> Common tab. You should see Country Code dropdown menu to set it to Australia.

Mar 25, 2008 2:47am starkey 4 post(s)	That dropdown menu is set to United States and the field is locked so I cannot change it. I am logging in on the super login. Is there another login I should know about? So far I have: Tried admin login. Tried super login. Reset to factory defaults. Tried admin and super login. Upgraded Firmeware to latest version, reset to factory defaults. Tried admin and super login. Tried super login on SSH connection with “set countrycode AU” and error given is “You are not allowed to change the country code”. Any more suggestions?

Mar 25, 2008 5:54am csannedhi Administrator 71 post(s)	If you are in US, you will get an AP with that particular country type. US customers are not allowed to change the country code because of FCC regulations. If you are in AU, you should check with your store to find out how you received a unit with US country settings.

Aug 28, 2008 2:14am Zoran 7 post(s)	Starkey, is you AP managed via ZoneDiroctor? If yes, hard reset your AP, plug in with your PC via Cat5 (network cable), log in to AP (defaulty IP should be 192.168.0.1) and then you should be able to change any settings. I’m in AUS and did get the Ruckus gear from US, and did not have problems to change the settings. Regards Zoran

Sep 18, 2008 5:48am starkey 4 post(s)	Thanks Zoran, but it was not that simple. I ended up following csannedhi’s advice and contacting my supplier, who in turn got me in touch with a Ruckus support tech in Hong Kong, who talked me through changing the country code via Telnet, after I had flashed another firmware. :)